Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
*
Will not fit models equipped with Air
Suspension Package
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75749F
Wrenches: 10mm, 11/16
Drill Bits: NONE
Remove in
step 2.
Figure 1.
j
Qty. (1)
3/8-16 U-Bolt
k
Qty. (2)
3/8-16 Hex Nut
l
Qty. (2)
3/8 Conical Washer
1.
Support the exhaust and remove exhaust from hangers so exhaust can be lowered out of the way.
2.
Remove the plastic fascia brackets (return to owner) shown in Figure 1. and the exhaust heat shield cover hardware, so sheild can move freely
above the exhaust.
3.
Remove the four (2 per side) lower M10 nuts from the bumper brackets (do not discard).
4.
Raise the hitch into position with side brackets installed on the bumper bracket bolts and loosely reinstall the M10 nuts removed in step 4.
5.
Raise the forward end of the hitch to the cross member under the car. Place U-bolt provided through cross member hole and into slotted holes
in hitch and install the 3/8 nuts and conical washers.
6.
Tighten from 10mm bolts to torque specs below and reinstall the heat shield. (note heat shield may need to bend a little to be reinstalled
around hitch.)
7.
Tighten rear U-bolt to torque specs below and reinstall exhaust on hangers.
8.
Using Zip ties provided. Zip tie hitch to the fascia where the removed brackets where located.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2012, Cequent Towing Products
Installation Instructions
Mercedes-Benz ML350*
(will not fit 2012 & newer ML350 DEISEL.)
Fascia
Sub Frame
2
3
Existing Nuts
Tighten all 3/8-13 GR5 fasteners with torque wrench to 30 Lb.-Ft. (41 N-M)
Tighten all M10 fasteners with torque wrench to 38 Lb.-Ft. (52 N-M)
Do Not Exceed Lower of Towing Vehicle Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV3, SUV4
Bumper Bracket
1
m
Qty. (5)
Zip Ties
Sheet 1 of 3
75376N
Part Numbers:
75749
44678
87624
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
4000 (1 816 Kg)
525 (238 Kg)
3500 (1 589 Kg)
525 (238 Kg)
4-18-12
Rev. A
Publicidad
Manuales relacionados para Cequent Towing Products 75749
Resumen de contenidos para Cequent Towing Products 75749
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 75376N 4-18-12 Rev. A 2012, Cequent Towing Products...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 1 de 3 75376N 4-18-12 Rev. A 2012 Cequent Towing Products...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. Hoja 1 de 3 75376N 4-18-12 Rev. A 2012 Cequent Towing Products...