Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Turn the locking ring (11) clockwise to the locked
position.
Hold the blow tube approximately 180mm above the
ground, switch on the appliance and using a sweeping
motion from side to side, advance slowly keeping the
accumulated debris/leaves in front of you (fig. H).
Once you have blown the debris/leaves into a pile, you
can convert to vacuum mode to collect the debris.
Removing the blow/vacuum tube (fig. I)
To disconnect the blow clamshell (6) or vacuum tube
(10) from the powerhead (13), turn the locking ring (11)
counter-clockwise to the unlock position, then press the
release button (12), making sure that the tube does not
fall to the ground.
The release button (12) will not operate if the locking
ring (11) is in the locked position.
Vacuum mode (fig. J - N)
Fit the bag assembly to the blowvac (figs. J, K, L)
For vacuuming/shredding, the collection bag (5) must
be fitted.
Locate the bag rim (23) into the bag holder channel (25)
making sure that the front of the bag is placed over the
vacuum outlet (24) (fig. J).
Slide the bag fully into the channel and press the latch
(26) to lock the handle into the bag top (fig. K and L).
Position the tube slightly above the debris/leaves.
Switch your blowvac on, and use a sweeping motion;
the debris/leaves will be sucked up the tube, shredded
and thrown into the collection bag (fig. M).
For stubborn debris/leaves your vacuum tube is
incorporated with a scraper (8). Use the scraper to
loosen the debris and continue to vacuum as normal.
As the bag fills, the power of the suction will decrease,
switch off the blowvac and unplug from the mains power
supply.
To remove the bag, press the latch (26) to disengage
from the bag holder and slide the bag out.
To empty, hold the plastic collection bag handle (4) and
grab the nylon handle (27) on the underside of the bag.
Turn the bag upside down and shake out any debris and
leaves.
Troubleshooting
Failure to
1 Check the connection to the power
operate
supply.
2 Check the fuse in the plug, if blown,
replace (UK only).
3 Check that the blow/vacuum tube
assembly is correctly fitted to the
powerhead
4 If the fuse continues to blow -
immediately disconnect from the
mains power supply and consult your
local Black & Decker authorised repair
agent.
5 Check the locking ring position.
Poor vacuum/
1 Switch off - disconnect from the mains
high pitched
power supply, debris should fall clear
whine
of the tube.
2 Remove and empty the collection bag.
3 Check that both the inlet and exit ports
on the vacuum tube are clear.
4 Remove any debris from the fan area.
5 If poor vacuuming continues -
immediately disconnect from the
mains power supply and consult your
local Black & Decker authorised repair
agent.
Poor shredding 1 Switch off - disconnect from the mains
power supply and remove the
collection bag.
2 Remove the vacuum tube and inspect
the fan.
3 Clean any debris from the fan blades.
4 If the fan is cracked or damaged, do
not use - consult your local Black &
Decker authorised repair agent.
Maintenance
Your Black & Decker appliance has been designed to
operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends
upon proper appliance care and regular cleaning.
Keep the appliance clean and dry.
Remove any leaves stuck to the inside of the
vacuum tube.
Regularly clean the ventilation slots with a clean,
dry paint brush.
To clean the appliance, use only mild soap and a damp
cloth. Never let any liquid get inside the tool and never
immerse any part of the tool into liquid. Do not use any
abrasive or solvent-based cleaner.
ENGLISH
9
Publicidad
Tabla de contenido
