Maintenance And Storage; General Recommendations - Surtek PP520A Manual De Usuario

a)Put the lever on the START position
b)Take the flame out and maintain it against
the superior handle, pull on the recoil starter
handle until you can feel resistance and then
pull harshly.
c) Put the lever on RUN position
WARNING: Blade is in action as soon as
engine started. While the machine is working
maintain the security handle (3) in working posi-
tion. The engine will stop as soon as you release
the engine control bar.
THE REGULATION METHOD OF THROTTLE
CONTROL CABLE:
The regulation method of throttle control cable
On the brake stand of flameout there are switch
of flameout, if the cable is elongates, make
throttle control against the superior handle
rocker of brake can't touch the switch of flame-
out spark plug do not create spark engine can't
run. This time you need regulate the cable.
The method is as follows
METHOD 1
1 Dismantle throttle control and Dismantle the
top of cable then use spanner Loosen the nut of
regulate the screw.
2 Revolve the regulate the screw to make the
plastics set lengthen then will avoid the length
of cable that has lengthen out.
3 After regulation fix the cable into the throttle
control , Simple method to put the throttle con-
trol into superior handle easy :
Put right end of the throttle control into the
superior handle first, then put the other end of
throttle control into the superior handle.
4 Tension the throttle control to against the
superior handle ,this time , the angle of rocker
of brake to cover is 90° or the distance of brake
stand to rocker of brake is 1- 2 mm otherwise if
it is no distance the cable will break off.
5 Use spanner screw down the nut after regula-
tion.
6 Contrarily Repeat the method above ,as far as
the spark plug create spark.
METHOD 2
Remove the dipstick and dismantle the end of
cable use tool to make a larger angle depend on
pull the support of cable.
2 IN 1 FUNCTION
MULCHING AND SIDE DISCHARGE
WHAT IS MULCHING ?
E N G L I S H •
When mulching, the grass is cut in one working
step, then finely chopped and returned
to the grass Strip as natural fertilizer.
HINTS FOR MULCH- MOWING
- Regular cut-back by max. 2 cm from 6 cm to 4
cm grass height
- Use a sharp cutting knife
- Do not mow wet grass
- Set max. motor speed
- Only move at walking pace
- Regularly clean mulching wedge,housing inner
Side and mowing blade.
STARTING OPERATION
Retrofitting for mulching mower
NOTE: Only with a stopped motor and stand-
still Cutter!
- Push the mulching wedge into the discharge
channel. Lock the mulching wedge with hous-
ing–the nose on the bottom side of mulching
wedge grip must snap into the opening on the
housing.
-Lower the discharge flap again.
Resetting for side-discharge mowing
NOTE: Only when motor and cutter are at
Standstill!
- Lift the discharge flap and remove the grass
catch box
- Mount the mulching wedge(see mulch Mow-
ing).
- Lift rear flap for side discharge.
- Mount the discharge channel for side discharge
on the support pin of the rear flap.
- Lower the rear flap–the rear flap lies on the
Discharge channel.

MAINTENANCE AND STORAGE

GENERAL RECOMMENDATIONS

• Always observe safety rules when perform-
ing any maintenance.
• The warranty on this lawn mower does not
cover items that have been subjected to oper-
ator abuse or negligence. To receive full value
from warranty, operator must maintain the
lawn mower as instructed here.
• Changing of engine-governed speed will
void engine warranty.
• All adjustments should be checked at least
once each season.
• Periodically check all fasteners and make
sure these are tight.
WARNING: Always stop engine, disconnect
spark plug, and ground against engine before
Us er 's M an u a l
10