Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
GB
5.3 - LEARNING OF THE FIRST OR ADDITIONAL TRANSMITTERS
PH.
DESCRIPTION
Press the control unit programming pushbutton twice in
1
quick succession. The LED blinks twice and the buzzer
sounds twice every 2 seconds.
Hold the control unit programming pushbutton. The LED
2
blinks and the buzzer sounds again.
The control unit signals the output selected by means of a
number of beeps and blinks. Whenever the pushbutton is
pressed again, the function will be changed as follows:
1 beep = output 1
3
2 beeps = output 2
The system will notify the user of the setting just made
by blinking the LED quickly and sounding the buzzer the
number of times equivalent to the output selected every
2 seconds.
Press the pushbutton of the transmitter to be saved. Once
4
it has been saved, the control nut will give two long blinks
of the LED and 2 long beeps of the buzzer.
5
To learn an additional transmitter, repeat point 4.
To terminate the transmitter saving procedure, wait for the
6
programming timeout, indicated by a long beep and a long
blink of the LED.
If the memory is full or the transmitter is already in the
Note
memory, the control unit will give 10 blinks and 10 beeps.
5.4 - PROGRAMMING THE OPERATING TIMEOUT
PH.
DESCRIPTION
Press the control unit programming pushbutton quickly.
1
The LED blinks and the buzzer sounds every 2 seconds.
Hold the programming pushbutton for more than 3 secon-
2
ds. The LED blinks once and the buzzer sounds.
Press the control unit programming pushbutton a number
of times equal to the number of operating hours to be
programmed:
first press = 0 hours
3
second press = 1 hour
.....
tenth press = 9 hours
The control unit blinks and beeps twice each time the
pushbutton is pressed.
Confirm the operating hours by pressing the control unit
programming pushbutton and holding it for more than 3
4
seconds. The control unit will give one long blink and one
long confirmation beep.
Press the control unit programming pushbutton a number
of times equal to the number of operating minutes to be
programmed:
first press = 0 minutes
5
second press = 1 minute
.....
sixtieth press = 59 minutes
The control unit gives 3 blinks and beeps three times each
time the pushbutton is pressed.
Confirm the operating minutes by pressing the program-
ming pushbutton and holding it for more than 3 seconds.
6
The control unit will give one long blink and one long
confirmation beep.
Press the control unit programming pushbutton a number
of times equal to the number of operating seconds to be
programmed:
first press = 1 second
7
second press = 2 seconds
.....
fifty-ninth press = 59 seconds.
The control unit gives 4 blinks and 4 beeps each time the
pushbutton is pressed.
Confirm the operating seconds by pressing the program-
ming pushbutton and holding it for more than 3 seconds.
8
The control unit will give one long blink and one long
confirmation beep.
6 - MOTOR MODE
6.1 - "ONE KEY" PROGRAMMING
EXAMPLE
Every radio pushbutton is memorised individually in SINGLE KEY mode, using
>2
the programming procedure to associate it to the function of the user's choice
(Tab 1), which will then be strictly associated to the pushbutton pressed.
x 2+
x 2
Tab.1
FUNCTION NO.
>3s
1
2
x 1+
x 1
3
4
5
x n
6
7
x n+
x n
8
9
6.2 - "PRESET" PROGRAMMING
A different procedure can be used to save a single 4-pushbutton transmitter in
"PRESET" mode.
In this mode, each key of the transmitter saved will have a specific preset fun-
x 1+
x 1
ction, since all the transmitter's keys will be saved (Tab. 2).
Tab.2
x 10+
x 10
FUNCTION NO.
1
2
3
EXAMPLE
4
>1
Warning: The same transmitter cannot be simultaneously saved in the same
x 1+
x 1
control unit in both "SINGLE KEY" and "PRESET" modes.
>3s
6.3 - LEARNING OF THE FIRST OR ADDITIONAL TRANSMITTERS
x 1+
x 1
PH.
DESCRIPTION
Press the programming pushbutton twice in quick succes-
1
sion. The LED blinks twice and the buzzer sounds twice
> n
every 2 seconds.
x 2+
x 2
Hold the programming pushbutton. The LED blinks and
2
the buzzer sounds again.
>3s
The control unit signals the operating mode selected by
means of a number of beeps and blinks. Whenever the
x 1+
x 1
pushbutton is pressed again, the function will be changed
as follows:
1 beep = single key - step-by-step (open-stop-close-stop)
2 beeps = single key - open/stop
> n
3 beeps = single key - close/stop
4 beeps = single key - hold-to-run step-by-step
x 3+
x 3
5 beeps = single key - hold-to-run open
3
6 beeps = single key - hold-to-run close
7 beeps = single key - stop
8 beeps = single key - open
9 beeps = single key - close
>>3s
10 beeps = preset programming
The control unit will notify the user of the setting just made
x 1+
x 1
by blinking the LED quickly and sounding the buzzer the
number of times equivalent to the function selected every
2 seconds.
Press the pushbutton of the transmitter to be saved. Once
> n
4
it has been saved, the control nut will give two long blinks
of the LED and 2 long beeps of the buzzer.
x 4+
x 4
5
To learn an additional transmitter, repeat point 4.
To terminate the transmitter saving procedure, wait for the
6
programming timeout, indicated by a long beep and a long
blink of the LED.
>>3s
If the memory is full or the transmitter is already in the
Note
memory, the control unit will give 10 blinks and 10 beeps.
x 1+
x 1
FUNCTION PROVIDED
STEP-BY-STEP (OPEN/STOP/CLOSE/STOP)
OPEN/STOP
CLOSE/STOP
HOLD-TO-RUN STEP-BY-STEP
HOLD-TO-RUN OPEN
HOLD-TO-RUN CLOSE
STOP
OPEN
CLOSE
FUNCTION PROVIDED
STEP-BY-STEP (OPEN/STOP/CLOSE/STOP)
OPEN/STOP
CLOSE/STOP
STOP
EXAMPLE
>2
x 2+
x 2
>3s
x 1+
x 1
x n
x n+
x n
x 1+
x 1
x 10+
x 10
Publicidad
Tabla de contenido
