GIESSE ST450 Manual De Instrucciones página 4

Instructions for the window maker
Read the instructions carefully before starting to install the
product.
Follow all the instructions as incorrect installation can lead to
serious injury. Incorrect installation may be a source of hazards.
Installation must be carried out by professionally competent staff.
Installation, electrical connections and adjustments must be
carried out in accordance with Good Practice and in compliance
with the relevant regulations. The drive system constructor is not
responsible for failure to comply with Good Practice when
constructing the casements for operation, or for any deformations
which may occur during use. The drive system constructor declines
all responsibility in the event of installation of components
incompatible with safety and trouble-free operation.
The window maker must check that the temperature range marked
on the operator is suited for the place of installation. The partly
completed machine is not suitable for installation in locations with
ionizing radiation; the installation and operating environment must
not generate risks for the operator. The installation location must be
well lit, assuming that the ambient lighting in the partly completed
machine's place of use is of normal intensity. Do not install the
product in locations with explosive atmosphere: flammable gases
or fumes constitute a serious safety hazard. Inspect the product for
damage before starting installation. Check that the existing
structure has the necessary strength and stability. Before starting to
install the drive system, make all structural modifications necessary
for compliance with the safety precautions and to protect or enclose
all zones with crushing, shearing or entrainment hazards, or hazards
in general.
Before installing the actuator, check that the sash (bottom or top
hung) is in good mechanical condition, correctly balanced and
opens and closes properly.
Make sure that during the opening and closing movement there are
no collisions between the sash and frame and that the sash does not
hook onto the frame. The sash must have free movement.
After installation, make sure that the mechanism is properly
regulated and that the system protection and each manual release
work properly.
Specifications
Nominal thrust and traction force: . . . . . . 450 N
Available travel: . . . . . . . . . . . . . . . . . . . . . . max 180 and 300 mm
Length of time for idle travel: . . . . . . . . . . . 12 sec.
Linear speed: . . . . . . . . . . . . . . . . . . . . . . . 23 mm/sec.
Single phase voltage: . . . . . . . . . . . . . . . . . 230 Volts ~
Frequency: . . . . . . . . . . . . . . . . . . . . . . . . . . 50/60 Hz
Current: . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.7 A ~
Consumption: . . . . . . . . . . . . . . . . . . . . . . . 150 Watts
Condenser: . . . . . . . . . . . . . . . . . . . . . . . . . 1 for 5 micro Farads
Overload switch: . . . . . . . . . . . . . . . . . . . . . YES
Automatic limit switch: . . . . . . . . . . . . . . . YES
Built-in relay . . . . . . . . . . . . . . . . . . . . . . . . YES
Parallel connection: . . . . . . . . . . . . . . . . . . YES
Protection rating: . . . . . . . . . . . . . . . . . . . . IP 55
Operating cycle . . . . . . . . . . . . . . . . . . . . . . T ON 2' / T OFF 30'
ISTRUZIONI - INSTRUCTIONS - INSTRUCTIONS - ANLEITUNG - INSTRUCCIONES - ИНСТРУКЦИЯ
Before connecting the electricity supply, check that the nameplate
data are the same as those of the electricity supply system.
Install a switch/omnipolar circuit breaker with contact opening gap
at least 3 mm (not supplied) on the electricity supply line.
Check that the upstream electricity supply system includes a
suitable RCD and overcurrent protection.
Packaging materials (plastic, polystyrene, etc.) must be disposed of
properly and must not be left within reach of children as they
constitute potential hazards. Genuine parts must always be used
when repairing or replacing products.
If the partly completed machine is installed in a position not easily
accessible to the operator, the structures needed to access the
working zone must be provided by the user in accordance with the
relevant safety regulations.
Safety Recommendations and Rules:
- N.B. The system is tested to withstand a maximum wind of 40 km
per hour with the sash open. It should therefore be connected to a
wind-rain guard control unit (Pv1) and an anemometer should be
used.
- GIESSE products should be installed by industry specialists who
provide guarantees of the necessary technical competence.
- Proceed in accordance with the constructor's instructions.
- The window maker must ensure that the device is installed and
operates correctly.
- Use of the product for purposes other than the intended purpose or
misuse is forbidden.
- Use genuine spare parts.
- Hazardous parts of the actuator must be installed at least 2.5 m
above floor level.
- In applications with a height off the ground of less than 2.5 m,
use the "dead man" control function.
- Applications with intensive use are not recommended.
All the specifications have been written and verified with our best
attention. We do not undertake responsability for possible errors
or omissions. We reserve the right to introduce changes relative
to technological progress. Guarantee: The guarantee conditions
can be checked in the price list on the basis of the commercial
agreements.
- 4/20 -
I0854000/05-2018