Black and Decker P2219 Manual Del Usuario página 5

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 24
Electrical safety
This charger is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
1. On/off switch
2. Lens
3. Bungee cord
4. Battery release button
5. Flashlight body
6. Pocket clip
Assembly
Installing the battery pack (fig. A)
Insert the metal terminal end of the battery pack (7) into
the battery compartment until you hear the lock click into
place and the VPX™ logo shows through the window
(6).
Warning! The battery will only fit one way, do not force it. If
the battery does not fit, remove it and put it in the other way.
Removing the battery pack (fig A)
Press the battery pack release button (4) and firmly pull
the battery pack (7) out of the battery compartment.
Charging the batteries (fig. B)
Warning! Do not charge battery packs at ambient
temperatures below 10 °C or above 40 °C.
The charger will not charge a battery pack if the cell
temperature is below approximately 0 °C or above
60 °C. The battery pack should be left in the charger
and the charger will begin to charge automatically when
the cell temperature warms up or cools down.
Plug in the charger (8) and switch on at the mains.
Insert the battery pack (7) into the charger. Make sure
that the battery pack is fully seated in the charger (8).
The charging indicator (9) will flash continuously
(slowly).
Leave the battery to charge for at least 5 to 6 hours.
The charge is complete when the charging indicator (9)
lights continuously
The charger and the battery pack can be left connected
indefinitely with the LED illuminated. The LED will
change to flashing (charging) state, as the charger
occasionally "tops off" the battery charge.
The charging indicator (9) will be lit as long as the
battery pack is connected to the plugged-in charger.
Charge discharged batteries within 1 week. Battery life
will be greatly diminished if stored in a discharged state.
Charge indicators
If the charger detects a problem with a battery pack, the
charge indicator (9) will flash at a fast rate.
If this occurs, re-insert the battery pack (7).
If the problem persists, put a different battery pack in the
charger to determine if the charger is OK.
If the new battery pack charges correctly, then the
original battery pack is defective and should be returned
to a service centre for recycling.
If the new battery pack gives the same indication as the
original, take the charger to be tested at an authorized
service centre.
Note: It may take as long as fifteen minutes to determine that
the pack is defective.
If the battery pack is too hot or too cold, the LED will
alternately blink fast and slow, one flash at each speed and
repeat.
Battery chargers - daisy chaining (fig. C)
Single and dual port chargers can be electrically connected
in any order up to a maximum of 4 chargers. Each charger
has a power-in cord (10) which plugs into the electrical outlet
and a power-out cord (11) which plugs into the next charger.
To connect the chargers in a daisy chain:
Plug the power-in cord (10) into an electrical outlet.
Remove the power-in cord from the next charger and
plug in the power-out cord (11) from the charger that is
now plugged into the outlet.
Repeat this process for the remaining chargers.
Chargers that are daisy chained together operate
independently as though each one was plugged into a
separate outlet, therefore a battery can be removed from
anywhere along the daisy chain without affecting the other
chargers.
Use
Operating the flashlight (fig. D)
Press the on/off switch (1) to turn the flashlight on.
Press the on/off switch (1) again to turn the flashlight off.
Pivoting lens (fig. E)
The lens can be pivoted to any angle from the in-line position
to 90° and can be placed on its edge with the lens pivoted
for hands-free operation.
Using the built-in bungee cord (fig. F)
The bungee cord (3) may be used to store or carry the
flashlight.
ENGLISH
5

Publicidad

Tabla de contenido
loading

Tabla de contenido