Intended Use - DeWalt DCD992 Manual Del Usuario

EnGLIsH
Belt hook
7
Mounting screw
8
Bit holder
9
Battery release button
10
Battery pack
11
Main handle
12
Side handle
13
Mode selector button
14
Date code
15

Intended Use

These drills/drivers/hammerdrills are designed for professional
drilling, percussion drilling and screwdriving applications. This
tool is compatible with Bluetooth® Battery Technology and with
the D WALT Tool Connect™ App.
e
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
These drills/drivers/hammerdrills are professional power tools.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Use only D
e
Inserting and Removing the Battery Pack
from the Tool (Fig. B, C)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool
Handle
1. Align the battery pack 11
handle (Fig. C).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the release button 10
out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
36
WALT battery packs and chargers.
11 is fully charged.
with the rails inside the tool's
and firmly pull the battery pack
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge button.
A combination of the three green LED lights will illuminate
designating the level of charge left. When the level of charge
in the battery is below the usable limit, the fuel gauge will not
illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Belt Hook and Magnetic Bit Holder (Fig. A)
(Optional Accessories)

WARNING: To reduce the risk of serious personal
injury, ONLY use the tool's belt hook to hang the
tool from a work belt. DO NOT use the belt hook for
tethering or securing the tool to a person or object during
use. DO NOT suspend tool overhead or suspend objects
from the belt hook.

WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook is secure.

CAUTION: To reduce the risk of personal injury or
damage, DO NOT use the belt hook to hang the drill
while using as a spotlight.
IMPORTanT: When attaching or replacing the belt hook
magnetic bit holder , use only the screw
9
Be sure to securely tighten the screw.
The belt hook 7 and magnetic bit holder
to either side of the tool using only the screw
to accommodate left- or right- handed users. If the hook or
magnetic bit holder is not desired at all, it can be removed from
the tool.
To move belt hook or magnetic bit holder, remove the screw
that holds it in place then reassemble on the opposite side. Be
sure to securely tighten the screw.
Variable Speed Trigger Switch (Fig. A)
To turn the tool on, squeeze the trigger switch
tool off, release the trigger switch. Your tool is equipped with
a brake. The chuck will stop as soon as the trigger switch is
fully released.
nOTE: Continuous use in variable speed range is not
recommended. It may damage the switch and should
be avoided.
Side Handle (Fig. A)

WARNING: To reduce the risk of personal injury, ALWAYS
operate the tool with the side handle properly installed.
Failure to do so may result in the side handle slipping
during tool operation and subsequent loss of control. Hold
tool with both hands to maximize control.
The side handle 13 clamps to the front of the gear case and
may be rotated 360˚ to permit right- or left-hand use. Side
7 or
that is provided.
8
9 can be be attached
8 provided,
8
. To turn the
1