Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Frame rail
Spare Tire
Hitch Shown In Proper Position
Equipment Required: Pullwires (provided)
Fastener Kit: 75281F & 75281B
Wrenches: 10mm, 18mm, 7/8"
Drill Bits: 3/8" & 1"
Note: Fasteners typical both sides
Frame rail
Existing
weldnuts
l
m
Installation for vehicles with O.E.M. Class 2 Integrated Hitch/Bumper
j
Qty. (6)
Carriage Bolt 1/2-13 X 1.75 GR5
k
Qty. (6)
Block
l
Qty. (6)
Conical Washer
Installation for vehicles with O.E.M. Class 2 Integrated Hitch/Bumper. (Figure 1)
1.
Remove existing bolts from inside frame rails. Return to owner.
2.
Relocate existing electrical bracket. Remove (2) screws and shift the bracket toward the drivers side using the inside screw
hole on bracket and outside weld nut (See Figure 5).
3.
Raise hitch into position and install conical toothed washers and hex bolts into the existing weldnuts.
4.
Using the pullwire feed carriage bolts and blocks thru access slot in end of the frame as shown in Figure 1. Using the kink
pullwire to keep block independent of bolt (See Figure 2). Feed the pullwire thru the existing slot and hitch.
5.
Attach conical toothed washer and hex nuts.
Note: Do Not use both Hitches at the same time. This may overload and cause damage to vehicle.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2005, 2006, 2007, 2009 Cequent Towing Products
Installation Instructions
Ford Escape
Mercury Mariner
Fascia
1-1/4" O.E.M.
Hitch
(Not on all
Vehicles)
j
k
l n
Figure 1.
Tighten all M12 CL10.9 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Tighten all 1/2-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
(Includes Hybrid)
(Includes Hybrid)
Mazda Tribute
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: SUV1, SUV2
WARNING: If vehicle is equipped with O.E.M. hitch
DO NOT use both Hitches at the same time. This may
overload and cause damage to vehicle.
Access slot
both sides
Existing O.E.M.
Hitch/Bumper
Before
Electrical
bracket.
m
Qty. (6)
Hex Nut 1/2-13
n
Qty. (4)
Bolt M12 X 1.75 X 45 CL10.9
Sheet 1 of 6
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
5000 (2270 Kg)
3500 (1589 Kg)
Kink pullwire to keep
blocks independent of
bolt.
Figure 2.
O.E.M. hitch
After
O.E.M. hitch
Figure 5.
75281N
5-1-09
Part Numbers:
75281
44527
70758
Max Tongue
WT (LB)
500 (227 Kg)
350 (159 Kg)
Existing
O.E.M.
Hitch/Bump
er
Rev. E
Form: F205 Rev A 5-6-05

Publicidad

loading

Resumen de contenidos para Cequent Towing Products 75281

  • Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 6 75281N 5-1-09 Rev. E 2005, 2006, 2007, 2009 Cequent Towing Products Form: F205 Rev A 5-6-05...
  • Página 2: Installation Instructions

    This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 2 of 6 75281N 5-1-09 Rev. E 2005, 2006, 2007, 2009 Cequent Towing Products Form: F205 Rev A 5-6-05...
  • Página 3 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 3 de 6 75281N 5-1-09 Rev. E 2005, 2006, 2007, 2009 Cequent Towing Products Form: F205 Rev A 5-6-05...
  • Página 4 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 4 de 6 75281N 5-1-09 Rev. E 2005, 2006, 2007, 2009 Cequent Towing Products Form: F205 Rev A 5-6-05...
  • Página 5 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque delestado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684 Hoja 5 de 6 75281N 5-1-09 Rev. E 2005, 2006, 2007, 2009 Cequent Towing Products Form: F205 Rev A 5-6-05...
  • Página 6: Números De Partes

    Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque delestado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684 Hoja 6 de 6 75281N 5-1-09 Rev. E 2005, 2006, 2007, 2009 Cequent Towing Products Form: F205 Rev A 5-6-05...

Este manual también es adecuado para:

4452770758