Lutron RadioRA-SP SRD-P3BRL-L Manual De Instrucciones

Wall Mount Template
Please Read Before Installing
The Pico wireless control can be mounted to a wall in three ways.
Choose the appropriate template and installation procedure listed
below for your application.
A—No Wallplate Template
B—Single Gang Template
C—Multiple Gang Template
A
No Wallplate Template
LUTRON
1. Carefully cut out the template below along the dashed line and tem-
porarily attach it to the wall at the desired mounting location.
2. Mark and drill the 3/16 in (5 mm) screw hole locations indicated
within the Wall Mount Plate on the template.
3. Remove template and insert one Screw Anchor into each of the
holes drilled in step 2, making sure they are flush with the wall.
4. Loosely mount the Wall Mount Plate to the wall with the Mounting
Screws. Check to make sure the Wall Mount Plate is level. Once the
Wall Mount Plate is level, tighten the screws.
5. Slide the Pico control down onto the Wall Mount Plate.
LUTRON
3/16 in (5 mm) Drill
(not included)
Wall Mount
Screw Anchor
Plate
Mounting Screw
PRINTING INSTRUCTIONS:
Lutron Elec tron ics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299
Made and print ed in the U.S.A. 7/09 P/N 044-156 Rev. B
C
Multiple Gang Template
Cut out to provide
existing control
3/16 in (5 mm) Drill
(not included)
Screw Anchor
Mounting Screw
As Applicable
PRINTING INSTRUCTIONS:
English
Pico wireless control 1. Carefully cut out the template below along the
TM
SRD-P3BRL-L, SRD-P3BRL-S
2. Mark and drill the 3/16 in (5 mm) screw hole
3. Remove template and insert one Screw Anchor into
2.7 in (68.6 mm)
when printed to
correct size
U.S. and foreign patents pending. Lutron, RadioRA, and the sunburst logo are registered trademarks and Pico is a trademark of Lutron Electronics Co., Inc.
©2009 Lutron Electronics Co., Inc.
1. Carefully cut out the template below along the dashed line that
represents the appropriate multiple gang application. Cut along
the solid line to provide clearance for any existing controls.
Temporarily attach the template to the wall at the desired
mounting location.
2. Mark and drill only the 3/16 in (5 mm) screw hole locations,
indicated within the Wall Mount Plate(s) and Wallplate Adapter
on the template, that will have a Pico control installed.
3. Remove the template and insert one Screw Anchor into each of
the holes drilled in step 2, making sure they are flush with the wall.
Cut out to provide
clearance for clearance for
existing control
Wall Mount Wall Mount Wall Mount
Plate
B
Single Gang Template
LUTRON
dashed line and temporarily attach it to the wall at
the desired mounting location.
locations indicated within the Wall Mount Plate and
Wallplate Adapter on the template.
each of the holes drilled in step 2, making sure they
are flush with the wall.
3/16 in (5 mm) Drill
(not included)
Screw Anchor
Mounting Screw
PAGE SIZE: 8.5 X 11 PAGE SCALING: NONE
4. Loosely mount the Wall Mount Plate to the wall with the
5. Slide the Pico control down onto the Wall Mount Plate.
6. Mount the Wallplate Adapter with the mounting screws provided
Cut out to provide
clearance for
existing control
Wall Mount
Plate Plate Plate
2-Gang Wallplate Adapter
(CW-2-XX)
PAGE SIZE: 8.5 X 11 PAGE SCALING: NONE
4. Loosely mount the Wall Mount Plate to the wall with
the Mounting Screws. Check to make sure the Wall
Mount Plate is level. Once the Wall Mount Plate is
level, tighten the screws.
5. Slide the Pico control down onto the Wall Mount Plate.
LUTRON
6. Mount the Wallplate Adapter with the mounting
screws provided with the Pico control and snap the
Wallplate onto the Wallplate Adapter. DO NOT use
the screws that came with the Wallplate Adapter.
Wall Mount
Plate
1-Gang Wallplate Adapter
(CW-1-XX)
Mounting Screws. Check to make sure the Wall Mount Plate is
level. Once the Wall Mount Plate is level, tighten the screws.
LUTRON
with the Pico control and snap the Wallplate onto the Wallplate
Adapter. DO NOT use the screws that came with the Wallplate
Adapter with openings where a Pico control will be installed.
Cut out to provide
clearance for
existing control
Wall Mount
Plate
3-Gang Wallplate Adapter 4-Gang Wallplate Adapter
(CW-3-XX)
4.7 in (119.4 mm)
when printed to
correct size
4.7 in
(119.4 mm)
when printed
to correct
size
(CW-4-XX)