Wireless Interface Connections; Bluetooth - Ford Connected Wall box Manual De Instalación

Electrical Characterist- IEC
EN
ics
does not comply with BS7671 for
connection to TN networks in the
Emitted interference: Class B
EMC class
(residential, business, commercial
Immunity: industrial areas
Overvoltage category
Protection class
A residual current circuit breaker
Protective devices
must be provided from the install-
ation side. See Criteria for the
Integrated power
meter
Connections
Mounted on-wall, or in-wall
Cable feed
Cross-section of the connection
Connection cross-sec-
cable must comply with local
tion
codes/regulations. Connection at
(wire dimension)
Type 2 charging cable according
Charging cable includ-
ing coupler
EN 62196-1 and EN 62196-2
7.4 kW (1 phase) Maximum capa-
Max. charging capa-
city (kW)
adjustable via DIP switches
11 kW (3 phase) Maximum capa-
adjustable via DIP switches
Communication &
features
IEC 61851-1:2017, Annex A
Vehicle–charger Com-
munication Protocol
(CP)
4
Electrical Characterist-
ics
Display
Network interfaces
United Kingdom.
Authentication and
Mobile communica-
areas)
tions
OCPP
II, as per EN 60664
Mechanical data
I
Dimensions (W × H ×
D)
Weight (including
electrical connection.
Wall Mount Bracket &
Accuracy +/- 5 % Charging Cable)
Installation height
IP protection class,
device
Protection against
Power Input inside.
mechanical impact
to
Ambient conditions
Operating temperat-
Cable length 7.5 m
ure range
Storage temperature
city
range (°C)
Altitude (m)
city
Certification compat-
ibility
Other standards and
guidelines
IEC Electrical Characterist-
ics
9 RGB LEDs
Wi-Fi / WLAN 802.11n - 150 Mbit/
s
Bluetooth (BLE 4.2) – Setup app
Version 1.6
258 x 450 x 141 mm
10.2 x 17.7 x 5.5 inches
6,02 kg
13.27 lbs
Minimally 900 mm / 35.5 inches
above floor level
measured to / from the bottom of
the device
IP65
IK10
Tested OCPP
backends
-30 °C to +50 °C
-22 °F to +122 °F
-40 °C to +85 °C
-40 °F to +210 °F
Max. 3,000 m above sea level
3.1
Max. 9,842 ft above sea level
3.1.1
The Bluetooth connection is used to set up the Wi-Fi AP (ac-
– 2014/53/EU (Radio Equipment
cess point) when starting up the wall box. Note that you
Directive) [OJ L 153, 22.5.2014, p.
cannot control the charging wall box through Bluetooth.
62-106]
– 2011/65/EU (RoHS-Directive)
[OJ L 174, 1.7.2011, p. 88-110]
SKLJ98-10C823-AA
IEC
– 2014/53/EU – Art.3 (1) a) Sicher-
heit
– EN IEC 61851-1:2019; EN
61439-1:2011; IEC 61439-7:2018,
IEC 62955:2018 (RDC-MD),
– EN 62233:2008
– 2014/53/EU – Art.3 (1) a) Sicher-
heit (Funkteil)
– EN 62368-1:2014; EN 62311:2008
– 2014/53/EU – Art.3 (1) b) EMV
– EN 61000-6-2:2005; EN
61000-6-3:2007 + A1:2011; IEC
61851-21-2:2018
– 2014/53/EU – Art.3 (1) b) EMV
(Funkteil)
– EN 301 489-1 V2.2.3 (2019-11); EN
301 489-17 V3.2.4 (2020-09)
– 2014/53/EU – Art.3 (2) Funk-
spektrum
– EN 300 328 V2.2.2 (2019-07); EN
301 893 V2.1.1 (2017-05)
– 2011/65/EU
– EN IEC 63000:2018
Ford OCPP (Open Charge Point
Protocol) server
NOTE
A shutdown, or a reduction in charging current, may occur
to prevent the wall box overheating. This is a safety fea-
ture.

Wireless interface connections

Bluetooth

Ford Connected Wall Box Installation Manual