Resetting Wireless Configuration; Wps Activation; Fm Radio; Fm Radio Station Playing - Rotel T14 Manual De Instrucciones

12
For Android device:
1. Launch the Play-Fi App on your device.
2. Run the Play-Fi App, tap on the "gear" icon in the top right, then tap
"More Settings..." > "Add Play-Fi Device" > "Search" in sequence. The
App will automatically find the T14 and prompt you to set it up. Tap the
"Set-Up" button.
3. If your Wi-Fi network is protected, enter the password. The App will
connect the T14 to the network.
4. When the T14 is connected to the network, the rear panel LED will stop
flashing and be solid blue, the front display will indicate "Connected".
Play-Fi
Connected
5. You're connected! From here, feel free to rename your device with the
preset names, create your own custom name, or skip this and just start
enjoying music.
Play-Fi Audio Streaming
Once properly configured, you can begin streaming audio to the T14.
Launch the Play-Fi App and select the device or multiple devices you want
to control. Then select an audio service to begin streaming audio.
The Home menu of the Play-Fi App displays the available source options.
Select "Music" to see all of your local music, or select from one of the
many great music service listed. For more information on the Play-Fi App
or controlling Play-Fi enabled devices please visit https://www.play-fi.com.

Resetting Wireless Configuration

To reset the Wi-Fi configuration settings on the T14, press and hold the Play-Fi
button o on the rear panel for 8 seconds until "Set-Up" shows on the
display. This will erase all Wi-Fi configuration options, including attached
wireless network and encryption key, if any, stored in the T14.
NOTE: This clears all Wi-Fi configuration settings and requires following
the Wi-Fi setup steps again. This is useful if you change the Wi-Fi network
settings or install new wireless network equipment.

WPS Activation

To activate the WPS function of the T14, enable the WPS function on your
Wi-Fi router by following the instructions provided by the manufacturer.
Then press the rear panel Play-Fi button for 3 seconds. If not successful the
WPS process will reset after about 90 seconds.
NOTE: This is an automatic configuration option available on some
wireless networking equipment and should only be used if you are
familiar with this process.

FM RADIO

Before listening to FM radio, make sure that the antenna has been properly
connected.

FM Radio Station Playing

1. Select the FM Button from the source button
show as below.
2. Turn the PUSH SELECT knob
3. To auto scan for an FM station, you can choose any of the steps below:

Storing a radio station in a preset

While a radio station is playing, push the memory button
then enter the 2 digit preset number where you want to save this station on
the numeric keypad
preset FM radio stations may be stored.

Playing a preset radio station

Anytime you are on the FM source you can select a preset station for listening.
1. From the numeric keypad
station.
2. Press the PRESET +/-

FM Settings Menu

Press the FM
3 sub-menus under FM setting.
• SCAN SETTINGS: Select between ALL STATION or STRONG STATIONS
• AUDIO SETTINGS: Select "STEREO OR MONO" or "MONO ONLY".
• FM PRESET: Displays all 30 of the FM preset stations and allows tuning
To make changes in the FM settings menu, turn the PUSH SELECT knob
on the front panel or the up/down arrow buttons on the remote control. To
save a change, press the PUSH SELECT knob
= I . The display will ENT button on the remote control.
95.25
MHz
M
[RDS TEXT]
8
arrow buttons on the remote control to change the frequency of radio
station. Turning the PUSH SELECT knob on the front panel or using the
up/down arrow buttons on the remote control one step at a time changes
the frequency one step.
• Turn the PUSH SELECT knob
• Press and hold the up/down arrow buttons on the remote control.
3 D , the display will show preset saved. Up to 30
3 D
H buttons on the remote control to display preset
numbers. Press the up/down
buttons on the remote control or turn the knob
select the desired station, then press the PUSH SELECT
panel or the ENT button on the remote control . Press the FM
again to exit the preset menu and go back to playing status.
= I button and toggle to the FM settings Menu. There are
ONLY.
FM SETUP
> STRONG STATIONS ONLY
ALL STATIONS
FM SETUP
*
> STEREO OR MONO
MONO ONLY
to the selected preset by pressing the PUSH SELECT
panel or the ENT button on the remote control.
T14 Network/FM/DAB+ Tuner
on the front panel or use the up/down
8
on the front panel quickly up or down.
9 E
, press the preset number of the desired
B arrow buttons or the PRESET +/-
8 on the front panel to
8
on the front
= I
*
8 on the front
8 on the front panel or the
button,
H
button
8