Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Part
Description
Bolt, Button Head M5 - 0.8 x 20mm
A
Nylon washers
B
Plus-nut inserts
C
Screw Phillips head M6 x 20mm
D
ROLA cover
E
F
Direct mount adapter base
G
Rubber mounting gasket
H
Brass Nut M6
I
Hex bolt M5 - 0.8 x 30mm
J
Hex nut M6
K
Flat washer - steel
L
Star washer M5
M
Hex key- 3mm
N
3.6mm (.125") Drill bit
O
.290" Dia. ("L") Drill bit
P
Silicone sealant
Tools required to install
A
F
C
C
G
D E
B
Precaution Warnings before beginning
Use of ROLA Direct Mount systems with bolts is intended for
sheet metal top installations.
Install requires drilling and permanent installation of
Adapters.
Installation requires some tools and skill. If concerned please
have professionally installed.
Placement of Direct Mounts onto Vehicle surface (truck roof shown)
Remove covers from adapter
bases if attached.
59754N Rev B
4-15-13
Direct Mount Adapter kit system DMK-R
For use on sheet metal surfaces
Use with ROLA APE and APX cross bar kits
Qty
8
8
8
1
4
4
4
4
1
1
1
8
1
1
1
1
Tools required:
A
Masking tape
B
Fine tip marker
C
C
Center punch
Center punch
H
H
D
8mm wrench
E
10mm wrench
F
Tape measure
G
Hammer
H
Drill motor
I
I
Safety glasses
Assemble cross bars to desired width and
attach to adapter bases
D
E
A
B
F
G
C
H
Caution- never exceed the load rating for your vehicle
(contact manufacturer for details), or that of your cross
bar system which ever is lower.
Printed in China
PART No.
I
J
K
L
M
Align cross bars on vehicle in desired
position. Consider accessory spacing
and potential underside interference
59754
P
O
N
Page 1 of 2
Publicidad
Manuales relacionados para Rola 59754
Resumen de contenidos para Rola 59754
- Página 1 Drill motor Safety glasses Precaution Warnings before beginning Use of ROLA Direct Mount systems with bolts is intended for Caution- never exceed the load rating for your vehicle sheet metal top installations. (contact manufacturer for details), or that of your cross Install requires drilling and permanent installation of bar system which ever is lower.
- Página 2 Install covers when cross bars are not installed to keep debris out of adapters ROLA carries a variety of cross bar styles and lengths to attach to our direct mount adapters. Cross Bars are sold with mounting hardware. Any weight carried on the vehicle will adversely affect its handling particularly in cornering or in a cross wind and the vehicle should therefore be driven with increased caution.
-
Página 3: Outils Nécessaires À L'installation
H Perceuse Lunettes de protection Mises en garde avant de commencer L'utilisation du système de montage direct ROLA avec Attention : Ne jamais dépasser la capacité de charge la boulons est destinée aux installations sur toit de tôle. moins élevée, soit celle du véhicule (consulter le L'installation nécessite le perçage et la pose permanente... - Página 4 Poser les capuchons avant que les traverses ne soient installées afin d'éloigner les débris à l'écart des adaptateurs. ROLA offre une variété de styles et de longueurs de traverses de toit à fixer à nos adaptateurs pour montage direct. Les traverses sont vendues avec la visserie de montage.
- Página 5 Kit adaptador para montaje directo del 59754 PARTE No. sistema DMK-R Para uso sobre superficies de metal laminado Use con kits de travesaños APE y APX de ROLA Parte Descripción Cant. Perno, cabeza de botón M5 - 0.8 x 20mm Arandelas de nylon...
- Página 6 ROLA vende una variedad de estilos de travesaños y longitudes para instalar con nuestros adaptadores de montaje directo. Los travesaños se venden con accesorios de montaje. Cualquier peso del vehículo afectará de manera adversa su manipulación especialmente en las esquinas o con el viento en contra, por lo cual el vehículo se debe conducir con mayor precaución.