Descargar Imprimir esta página

Freestyle NAVIGATOR 3.0 Manual Del Usuario página 2

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 3
TO USE THE RECALL FUNCTION:
1. Press S3 button to select RECALL
mode.
2. Press S1 button to scroll through
the recorded individual lap time and
total elapsed time.
NOTE: The recall function is available
only when there is lap record. The
message "NO LAPS" will be displayed
if there is no lap record.
NOTE: The lap record will be cleared
when the chronograph is reset.
TO SET THE TIMER:
1. Press S3 button to select TIMER
mode.
2. Press and hold S2 button for
approximately 2 seconds, the timer
selection will blink.
3. Press S1 button to toggle between
timer interval 1 and timer interval 2
to set.
4. Press S3 button, the second digits
will blink.
5. Press S1 button to set the second
digits. Holding down the button will
speed up the process.
6. Press S3 button, the minute digits
will blink.
7. Press S1 button to set the minute
digits. Holding down the button will
speed up the process.
8. Press S3 button, the hour digits will
blink.
9. Press S1 button to set the hour
digits. Holding down the button will
speed up the process.
10. Press S3 button, the action-at-end
selection will blink.
11. Press S1 button to select among CS
(Count Stop), CR (Count Repeat)
and CCU (Count Up).
12. When finished making all the set-
tings, press S2 button to confirm.
NOTE: Illustration of the action-at-end
selections:
a) CS (Count Stop) – the timer will
stop when the countdown reaches
zero.
b) CR (Count Repeat) – the timer
will repeat the countdown when the
countdown reaches zero.
c) CCU (Count Up) – the timer count
up to a maximum of 23 hours 59
minutes and 59 seconds when the
countdown reaches zero.
NOTE: The timer cannot be activated
if the value of timer interval 1 is set
as 0:0'00".
TO USE THE TIMER:
1. Press S3 button to select TIMER
mode.
2. The timer will be displayed in its
current state – reset, running, or
stopped.
3. To resume a counting, press S1
button to resume from where it left
off.
4. To start a new counting, reload the
timer first.
Press S1 button to stop counting
and then press S2 button.
5. After reaching zero in a countdown,
a tune will be emitted. To stop the
tune, press any button.
NOTE: You can leave the timer running
while switching over to other operating
modes.
TO SET THE ALARM:
1. Press S3 button to select ALARM
mode.
2. Press S2 button to select among
alarm entries 1, 2 and 3 to set.
3. Press and hold S2 button for
approximately 2 seconds. The
minute digits will blink.
4. Press S1 button to set the minute
digits. Holding down the button will
speed up the process.
5. Press S3 button, the hour digits will
blink.
6. Press S1 button to set the hour
digits. Holding down the button will
speed up the process.
7. Press S3 button the alarm
frequency will blink.
8. Press S1 button to select among
daily (DL Y) and individual day (of
the week) only – Sunday (SUN),
Monday (MON, Tuesday (TUE),
Wednesday (WED), Thursday (THU),
Friday (FRI) and Saturday (SAT).
9. When finished the settings, press
S2 button to confirm.
NOTE: The alarm will automatically be
activated after being set.
NOTE: The alarm will work according
to HOME TIME or FOREIGN TIME (de-
pends on your selection in time mode).
TO USE THE ALARM:
In ALARM mode,
1. Press S2 button to select among
alarm entries 1, 2 and 3 to set.
2. Press S1 button to activate the
alarm. The alarm indicator
be displayed.
3. Press S1 button again to deactivate
the alarm. The message "OFF" will
be displayed.
WHEN AN ALARM GOES OFF:
A 20-second alarm tune will be emitted
at the designated time when the alarm
is activated. To stop the tune, press
any button.
TO USE THE BACKLIGHT:
Press S4 button to turn on the back-
light for approximately 3 seconds.
TO USE THE FREELIGHT:
Press and hold S4 button for 3 seconds
to activate the freelight. The bulb icon
will be displayed to indicate this
feature is on. In this mode, you can
activate the backlight by pushing any
one of the four buttons. Freelight will
automatically turn off after 6 hours.
To deactivate the freelight, press and
hold S4 button for 3 seconds. The bulb
icon
will disappear.
will
To reduce carbon foot print, these
Freestyle instructions are printed with
soy inks on recycled paper.
ENGLISH

Publicidad

loading