Publicidad
Enlaces rápidos
Thank you for choosing EAntenna.
All our products are manufactured and developed with the best materials on the market, to offer the best qualities and guarantees to our
customers.
The LFA antennas have an input impedance of 50 Ohm in the antenna, so no coupling is necessary. The loop is at the same time a coupling
system and director element and this presents many advantages when modeling.
The 'real' impedance of each LFA varies greatly. But, the impedance presented at the antenna entry point is always 50 Ohm. Therefore, there
is no limitation on the results of any optimization tool achieved with a single input impedance, but it manages to change the width and length of
the loop keeping the impedance at 50 Ohm. This feature is very important to ensure good performance, bandwidth and low SWR in the
antenna.
This additional flexibility also allows more lateral lobes to be suppressed and a better front-to-back (F / B) ratio compared to traditional Yagis.
With time it is possible to achieve an excellent balance between design, F/B, gain and bandwidth.
Additionally, the proximity of the loop and the antenna entry point make the LFA less susceptible to noise and static nearby. In addition, the low
level of the LFA lateral lobes provides a winning formula for an antenna with super low noise!
We detail the materials used, for their best use and assembly. All the fittings are made of stainless steel and the aluminum is made of T6061 or
T6063 alloy, known as Duralumin that offers the best conditions to be weatherproof, the force of the wind and the best conductivity. The
plastics used, are Polyamide and offer the best hardness and durability for years and years.
We offer warranty on operation, and warranty on hardware, delivering the hardware kit with some additional pieces for possible losses or
forced breaks. In addition, we offer Allen keys and fixed mounting elements.
In the following pages you can see detailed graphics of the parts.
Peso: 5,1 Kg.
Max. Potencia: 5,0 kW
yagi antenna
yagi antenna
3,43m
70LFA5
70LFA5
Artkl. 17800.04-5
Rev. V1.2 - 07/10/2020
Publicidad
Manuales relacionados para EAntenna 70LFA5
Resumen de contenidos para EAntenna 70LFA5
- Página 1 70LFA5 70LFA5 Artkl. 17800.04-5 Thank you for choosing EAntenna. All our products are manufactured and developed with the best materials on the market, to offer the best qualities and guarantees to our customers. The LFA antennas have an input impedance of 50 Ohm in the antenna, so no coupling is necessary. The loop is at the same time a coupling system and director element and this presents many advantages when modeling.
- Página 2 ENGLISH ESPAÑOL 2,112m 0,205m ALIMENTACION FEEDPOINT 0,205m 0,387m 0,592m +/- 1,802m 0,391m 0,983m 1,972m Placa Mástil Mast Plate +/- 1600mm 1,181m 2,164m 1,888m 1,216m 3,38m 1,852m...
- Página 3 ESPAÑOL Para montar el BOOM, tiene que hacer coincidir frontalmente las partes de boom que tienen la misma letra ( p.ej: A-A, B-B, C-C etc), y una vez hecho, las placas (EA010039) se van fijando con los tornillos DIN 933 M6X16 y arandela DIN 9021 M6. Se recomienda poner todas los tornillos y arandelas antes de fijarla a tope para no dañar ninguna rosca del BOOM.
- Página 4 ESPAÑOL El ensamblaje de los elementos, una vez seleccionados todos las longitudes, colocar en cada mitad de 13mm Ø frontalmente, introduciendo uno a uno, los tubos de 10mm Ø x 200mm (50LFA6XL IN) en una de las mitades. Una vez ya fijada la primera parte de un elemento, introducir la siguiente mitad y fijarla de nuevo con los tornillos DIN 7984 M4X12 que aparece detallado debajo.
- Página 5 ENGLISH The assembly of elements, once selected all lengths, place in each half of Ø 13mm front, introducing one by one, the tubes of 10mm diameter x 200mm (50LFA6XL IN) in one of the halves. Once fixed and the first part of an item, enter the next half and secure again screws DIN 7984 M4X12 which is detailed below.
- Página 6 PLACAS SUJECIÓN MÁSTIL ESPAÑOL La placa de sujeción BOOM/MÁSTIL (EA013013) de 200X100X6mm consta de 8 agujeros; 4 gruesos para los abarcones redondos y 4 para los abarcones cuadrados que sujetan el BOOM. Los 4 agujeros de mayor grosor tienen la función de que hagan la mayor fuerza sobre el mástil, mediante abarcones redondos de M8. Los abarcones redondos de M8 (A-0163), van fijados mediante arandela DIN 9021 M8 y tuerca DIN 934 M8 proporcionadas en el mismo abarcón, y fijada al mástil con la Mordaza (23035.50).
- Página 7 MAST TO BOOM PLATE ASSEMBLY ENGLISH The clamping plate BOOM / MAST (EA013013) 200X100X6mm consists of 8 holes; 4 thick for round U-bolts and 8 square U-bolts for securing the BOOM. The 4 holes are thicker function that make the greatest force on the mast by means of M8 round U-bolts. Round U-bolts M8 (A-0163), are secured by washer DIN 9021 M8 and nut DIN 934 M8 provided in the same U-bolt, and fixed to the mast with mounting block (23035.50) Detailed drawings for further illustration: (EA013013)
- Página 8 ESPAÑOL Ajuste del ROE/SWR: Una vez posicionada la antena con sus medidas, quizás necesite algún retoque para conseguir la ROE/SWR deseada. Desplazando la pieza curva hacia adentro o hacia afuera varios milímetros, es la forma de hacerlo. Buscando que el centro de Frecuencia esté...
- Página 9 ENGLISH Adjusting SWR: Once positioned the antenna with your measurements, you may need some fine-tuning to get the SWR desired. Shifting the curve piece inward or outward several millimeters, is the way to go. Looking to the center frequency is 70,200 MHz in the lower SWR.
-
Página 11: Plotter De Elevación
ENGLISH ESPAÑOL Plotter de Elevación... - Página 12 ENGLISH ESPAÑOL Plotter de Azimut...
- Página 13 ENGLISH ESPAÑOL Gráfico de R.O.E.
- Página 15 ENGLISH ESPAÑOL PACKING LIST BOLSA 1 - BAG #1 LISTA DE PIEZAS PART # DESCRIPCION MEDIDAS CANTIDAD IMAGEN PIEZA Nº DESCRIPTION SIZES QUANTITY PART IMAGE Placa Mástil/Boom 200 x 100 x 6mm EA013013 Mast and Boom plate Abarcon A-0163 50mm, M8 U-Bolt.
- Página 16 PACKING LIST ENGLISH ESPAÑOL LISTA DE PIEZAS BOLSA 3 - BAG #3 PART # DESCRIPCION MEDIDAS CANTIDAD IMAGEN PIEZA Nº DESCRIPTION SIZES QUANTITY PART IMAGE Plásticos 13mm Ø EAHYP013 Plastic Blocks Tornillo Allen DIN 912 M6x40mm S912-9640 Allen DIN 912 Screw Tuerca Autoblocante DIN 985 S985-906 DIN 985 LOCK NUT...
- Página 17 DESCRIPCION MEDIDAS CANTIDAD IMAGEN PIEZA Nº DESCRIPTION SIZES QUANTITY PART IMAGE 1715mm x 30mm 70LFA5 1715mm x 30mm 70LFA5 Pieza lateral Loop 387mm x 120mm x 10 mm Ø EALOOP38710 Loop Driven Pieza unión elementos 200mm x 10mm Ø EA0120010...