Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Thank you for choosing EAntenna.
All our products are manufactured and developed with the best materials on the market, to offer the best qualities and guarantees to our
customers.
The LFA antennas have an input impedance of 50 Ohm in the antenna, so no coupling is necessary. The loop is at the same time a coupling
system and director element and this presents many advantages when modeling.
The 'real' impedance of each LFA varies greatly. But, the impedance presented at the antenna entry point is always 50 Ohm. Therefore, there
is no limitation on the results of any optimization tool achieved with a single input impedance, but it manages to change the width and length of
the loop keeping the impedance at 50 Ohm. This feature is very important to ensure good performance, bandwidth and low SWR in the
antenna.
This additional flexibility also allows more lateral lobes to be suppressed and a better front-to-back (F / B) ratio compared to traditional Yagis.
With time it is possible to achieve an excellent balance between design, F/B, gain and bandwidth.
Additionally, the proximity of the loop and the antenna entry point make the LFA less susceptible to noise and static nearby. In addition, the low
level of the LFA lateral lobes provides a winning formula for an antenna with super low noise!
We detail the materials used, for their best use and assembly. All the fittings are made of stainless steel and the aluminum is made of T6061 or
T6063 alloy, known as Duralumin that offers the best conditions to be weatherproof, the force of the wind and the best conductivity. The
plastics used, are Polyamide and offer the best hardness and durability for years and years.
We offer warranty on operation, and warranty on hardware, delivering the hardware kit with some additional pieces for possible losses or
forced breaks. In addition, we offer Allen keys and fixed mounting elements.
In the following pages you can see detailed graphics of the parts.
Peso: 2,9 Kg.
Max. Potencia: 10,0 kW
yagi antenna
yagi antenna
70LFA3
70LFA3
17800.04-3
1,47m
Rev. V1.6 - 24/03/2021

Publicidad

loading

Resumen de contenidos para EAntenna 70LFA3

  • Página 1 70LFA3 70LFA3 17800.04-3 Thank you for choosing EAntenna. All our products are manufactured and developed with the best materials on the market, to offer the best qualities and guarantees to our customers. The LFA antennas have an input impedance of 50 Ohm in the antenna, so no coupling is necessary. The loop is at the same time a coupling system and director element and this presents many advantages when modeling.
  • Página 2 SPECIFICATIONS 70LFA3 Elements: Frequency Range: 70,0~70,5 MHz. 14,0..21,0 MHz. Gain: 8,66 dBi F/B: 22,44 dB 3500 KHz. 3800 KHz. SWR: 1,0:1~1,2:1 Ω Impedance 50 Ohms Max. Power: 5 kW. 300 W. Boom Length: 1,47m Wind Survival ≥ 200kmh / ≥ 125mph Weight: 2,5 Kg.
  • Página 3 ENGLISH ESPAÑOL...
  • Página 4 ESPAÑOL El primer paso de ensamblaje de los elementos es colocar en orden por diámetros según la pagina 2. Una vez hecho esto tener en cuenta que en cada extremo de los elementos hay una parte de cada tubo que tiene los agujeros mar gruesos. Estos son los que van en el extremo hacia el extremo de la antena, ya que los agujeros anchos son donde entra la cabeza del tornillo DIN 7984 y presiona al tubo interior.
  • Página 5 ENGLISH The first step of assembling the elements is to place in order by diameters according to page 2. Once this is done keep in mind that at each end of the elements there is a part of each tube that has thick sea holes. These are the ones that go at the end towards the end of the antenna, since the wide holes are where the head of the DIN 7984 screw enters.
  • Página 6 PLACAS SUJECIÓN MÁSTIL ESPAÑOL La placa de sujeción BOOM/MÁSTIL (EA013018) de 200X100X6mm consta de 8 agujeros; 4 gruesos para los abarcones redondos y 4 para los abarcones cuadrados que sujetan el BOOM. Los 4 agujeros de mayor grosor tienen la función de que hagan la mayor fuerza sobre el mástil, mediante abarcones redondos de M8. Los abarcones redondos de M8 (A-0163), van fijados mediante arandela DIN 9021 M8 y tuerca DIN 934 M8 proporcionadas en el mismo abarcón, y fijada al mástil con la Mordaza (23035.50).
  • Página 7 MAST TO BOOM PLATE ASSEMBLY ENGLISH The clamping plate BOOM / MAST (EA013018) 200X100X6mm consists of 8 holes; 4 thick for round U-bolts and 4 square U-bolts for securing the BOOM. The 4 holes are thicker function that make the greatest force on the mast by means of M8 round U-bolts. Round U-bolts M8 (A-0163), are secured by washer DIN 9021 M8 and nut DIN 934 M8 provided in the same U-bolt, and fixed to the mast with clamp (23035.50).
  • Página 8 ESPAÑOL Ajuste del ROE/SWR: Una vez posicionada la antena con sus medidas, quizás necesite algún retoque para conseguir la ROE/SWR deseada. Desplazando la pieza curva hacia adentro o hacia afuera varios milímetros, es la forma de hacerlo. Buscando que el centro de Frecuencia esté...
  • Página 9 ENGLISH Adjusting SWR: Once positioned the antenna with your measurements, you may need some fine-tuning to get the SWR desired. Shifting the curve piece inward or outward several millimeters, is the way to go. Looking to the center frequency is 70,200 MHz in the lower SWR.
  • Página 11: Plotter De Elevación

    Plotter de Elevación...
  • Página 12 Plotter de Azimut...
  • Página 13 Gráfico de R.O.E.
  • Página 15 PACKING LIST BOLSA 1 - BAG #1 LISTA DE PIEZAS PART # DESCRIPCION MEDIDAS CANTIDAD IMAGEN PIEZA Nº DESCRIPTION SIZES QUANTITY PART IMAGE Placa Mástil/Boom 100 x 100 x 6mm EA013018 Mast and Boom plate Abarcon A-0163 M8 x 50mm U-Bolt 23035.50 Mordaza...
  • Página 16 ESPAÑOL ENGLISH BOLSA 3 - BAG #3 PART # DESCRIPCION MEDIDAS CANTIDAD IMAGEN PIEZA Nº DESCRIPTION SIZES QUANTITY PART IMAGE Placa para Elementos 150x50x4mm EA010026.4 Elements plates Tornillo Allen DIN 912 S912-9620 M6x20mm Allen DIN 912 Screw DIN 9021 S9021-96 Abrazadera Sin-Fin 8-12mm P0100022...
  • Página 17 MEDIDAS CANTIDAD IMAGEN PIEZA Nº DESCRIPTION SIZES QUANTITY PART IMAGE 1470mm x 30mm 70LFA3 Pieza lateral Loop 418mm x 120mm x 6mm Ø EALOOP41806 Loop Driven DE1 EXCITADO 1200mm x 13mm Ø DE1 DRIVEN DE2 EXCITADO 1200mm x 13mm Ø...

Este manual también es adecuado para:

17800.04-3