Marking A Track; Radio; Manual Tuning; Preset Tuning - Panasonic SC-AK321 Instrucciones De Funcionamiento

Sistema estereo con reproductor de discos compactos
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

How discs with MP3 differ from CDs

Marking a track

Remote control only
You can mark one track each on the discs loaded so that you can
start play from them later.
To mark a track number
1
During play or stop
Select your desired track.
(For MP3, refer to "Track skip play" on page 10.
For CD-DA, press the numbered buttons.
To select track 10 or over, press [X10] then the two digits.)
2
Hold down [MARKER] until "STORING" blinks on the
display.
The selected track is stored in the marker of the current disc.
Note
If a track is already stored in the marker, it will be replaced next time
you store a new track in the same marker.
To recall a marked track number in the current disc
During play or stop
Press [MARKER] to recall a marker.
Play starts from the track recalled.
Note
"NO MARKER" indicates that the marker in the current disc is empty.
The marker memory is cleared when you open the CD tray.
For CD-DA, you cannot use this function during 1-RANDOM play
and A-RANDOM play.
You cannot use this function during program mode.

Radio

Manual tuning

1
Press [TUNER, BAND] to select band.
The unit comes on.
Every time you press the button:
FM ↔ AM
2
Press [PLAY MODE] on the remote control to select
"MANUAL".
Every time you press the button:
MANUAL ↔ PRESET
3
Hold down [g/REW/3] or [f/FF/4] for a moment
to search for a station.
The frequency stops when it finds a clear station.
To stop during the process, press [g/REW/3] or [f/FF/4].
Under excessive interference, a station may not be found.
Press [g/REW/3] or [f/FF/4] repeatedly to tune step-by-
step.
"TUNED" is displayed when a radio station is tuned.
"ST" is displayed when a stereo FM broadcast is being
received.
If noise is excessive in FM
Remote control only
Hold down [PLAY MODE] to display "MONO"
Monaural sound is selected and noise reduces when reception is
weak.
Hold down [PLAY MODE] again to cancel the mode.
"MONO" is also cancelled if the frequency is changed.
All manuals and user guides at all-guides.com
Main unit only
PL
GCP
Hold down [TUNER, BAND]. The display changes in a few seconds to
show the current minimum frequency. Continue to hold down the
button until the minimum frequency changes. The step is changed.
Repeat the above to change the step back.
Note
Remote control only
There are two methods of pre-setting stations.
Automatic presetting : All the stations the tuner can receive are
Manual presetting
Up to 15 stations each can be set in the FM and AM bands.
Preparation:
Press [TUNER, BAND] to select "FM" or "AM".
Do the following once each for FM and AM.
Preparation: Tune to the frequency where pre-setting is to begin.
Hold down [PROGRAM] until the frequency changes.
The tuner presets all the stations it can receive into the channels in
ascending order. When finished, the last station memorized is tuned in.
Pre-set the stations one at a time.
1 Press [PROGRAM] then press [g, REW/3 ] or
2 Press [PROGRAM] then press [g, REW/3 ] or
3 Press [PROGRAM].
The station occupying a channel is erased if another station is preset
in that channel.
Press the numbered buttons to select the channel.
To enter channel 10 or over, press [X10], then the two digits.
.
1 Press [PLAY MODE] to select "PRESET".
2 Press [g, REW/3] or [f, 4/FF] to select the
Radio
Allocation setting
: By adjusting the allocation, you can enable this tuner to receive
FM broadcasts allocated in 0.1MHz steps.
: By adjusting the allocation, you can enable this tuner to receive
AM broadcasts allocated in 10 kHz steps.
After changing the "allocation" setting, the frequencies you previously
preset in the memory will be cleared.
Sound is momentarily interrupted if you load/unload tapes while
listening to an AM broadcast.

Preset tuning

preset.
: You can select the stations to preset and the
order they are preset in.
Automatic presetting
Manual presetting
[f, 4/FF] to tune to the desired station.
[f, 4/FF] to select a channel.
Selecting channels
OR
channel.
13
RQT7340

Publicidad

Capítulos

Tabla de contenido
loading

Tabla de contenido