Declaration Of Conformity - Hoffman Berkel PROXIMA 800 Manual Del Usuario

DESCRIPTION
Circular blade professional
slicer machine suitable for
cutting only the food products
of the types and within the di-
mensional limits indicated in
this manual. The main parts of
the machine are shown in the
general component diagram
reported in picture 2. Electrical
diagrams are reported in pic-
ture 1.
DECLARATION
OF CONFORMITY
The machines described in this
manual comply with Direc-
tives 2006/42/CE, 2006/95/
CE, 2004/108/CE, 2003/108/
CE, 2011/65/CE, Regulation
(EC) 1935/2004 and related
harmonized standards as EN
1974:1998 +A1, EN60204-1,
EN60335-1, EN60335-2-64.
SAFETY
Pay attention to the following
basic safety precautions:
- read all the instructions be-
fore using the machine;
- this product is not intended
to be used by children;
- operate the machine only if
properly trained and in perfect
psycho-physical conditions;
- do not use the machine in any
way other than what indicated
in this manual;
- use the machines only in full
structural, mechanical and sys-
tem efficiency;
- install the machine in con-
formity to the instructions
indicated in the "Installation"
section;
- install the machine in a loca-
tion out of the reach of person-
nel unauthorized to operate it
and especially out of the reach
of minors;
- stay highly concentrated
when using the machine and
avoid any distraction during
use;
- do not allow the machine to
be used by others who have
not read and fully understood
the content of this manual;
- do not wear baggy clothing or
clothing with open sleeves;
- do not allow anyone else,
other than the operator, to ap-
proach during product cutting
operations;
- do not remove, cover or
modify the tags located on the
machine body and, in case of
damage of these, replace them
promptly;
- do not remove the transpar-
ent guards and do not modify
or bypass any mechanical and
electrical protective devices;
- slice only the permitted prod-
ucts, do not attempt cuts on
prohibited type products;
- always keep clean and dry the
sliced product resting surface,
the work area all around the
machine and the operator floor
area;
- do not use the machine as
a resting surface and do not
place any objects on it other
than food used for cutting op-
erations;
- do not use the slicer when,
due to normal wear, the dis-
tance between the edge of
the blade and the blade guard
ring exceeds 6 mm. In this case,
contact the manufacturer or to
one of the Authorized Service
Centers to change the blade;
- do not use the machine with
temporary or non-insulated
cables, power strips or exten-
sion cords;
- periodically check the condi-
6
tion of the power supply cord
on the machine body. When
necessary, have qualified per-
sonnel replacing it;
- immediately stop the ma-
chine in the event of a defect,
abnormal operation, suspicion
of breakdown, incorrect move-
ment, unusual noises;
- before cleaning or carrying
out maintenance, disconnect
the machine from the electri-
cal supply;
- use protective gloves for
cleaning and maintenance op-
erations;
- place and remove the goods
to be sliced on the sliding plate
only with the carriage com-
pletely pulled back and with
the thickness adjustment knob
placed in the safety position
(on the 0 position);
- for movement of the meat
table during cutting operations
use only the handle located on
the arm or the product presser
grip;
- never put your hands on the
food product while slicing. Al-
ways keep your hands behind
the protection devices and far
from the blade;
- use of cutting accessories
which were not provided by
the manufacturer with the ma-
chine is prohibited.
The manufacturer declines any
responsibility coming from in-
appropriate use, modifications
and/or repairs carried out by
the user or unauthorized per-
sonnel, use of replacement
parts that are not original or
not specific for the machine
model.
The machine shall not be used
in open areas and/or areas
which are exposed to atmos-
pheric agents and in environ-
ments with vapors, fumes or
corrosive and/or abrasive pow-