Publicidad
Installation and operating instructions
EN
Dear Buyer, Thank you for purchasing our product! We hope that it will give a lot of joy to your children and rest periods to you.
Please read this manual carefully before using this product. We also advise to keep it throughout the use of the product. Please follow all instructions of
assembly and use of this product that are mentioned in this manual. The assembly of the product is fairly simple and do not require special skills so you
can do it on your own. Follow the assembly steps and assemble the product only in the order shown in the images. A correct assembly of the product
is crucial to the long lifetime of the product, as well as to the safety of your children.
Before starting the assembly, choose a spot in your yard. The spot where you plan to place the product must be big enough, level and free of other
objects (see Image 1). The product must be placed in the distance of at least 2 metres from other objects in your yard, for example, house, garage,
fence, trees and their hanging branches, clotheslines, driveway or electric lines (see Image 2). To prevent the surface of the slide from heating up, place
the product in such a way that the surface of the slide would not face south. The product is intended to be placed on a soft ground cover, such as a
backyard lawn or a specially prepared area. The product must not be placed on a hard material surface, for example, asphalt, concrete or pavement.
When the product is assembled and placed in the appropriate spot, check if it stands straight. To verify this, you can use a spirit level by placing it in
different directions on the platform. If the product does not stand straight, use a spade and dig out earth under the highest leg of the product. Repeat
this step if necessary, until the product stands straight (see Image 3). After assembly, clean every wood component from splinters that could appear
during assembly, using sand paper.
If you wish to add accessories to the product, please use only manufacturer's original accessories. Mount the accessories to the product following their
assembly instructions.
Attention! The product must be assembled by adults only. Children are allowed to use the product
only when it is fully assembled. We recommend to use the product only in the presence of adults.
Prevent the product from being used improperly that may affect its durability and put the safety
of the children at risk.
Examine the product once in three months to see if there is any damage to it. Pay special attention to the plastic parts and swing mounts to check
for any damage, such as cracks, bumps or sharp protrusions. Make sure that there are no cracks in the wooden parts that may affect the safety of the
structure. Make sure that the joints of the parts are not loose. If there are resin stains on the wooden parts, clean them with an appropriate cleaner.
Damaged edges, splinters on wooden parts must be cleaned with sand paper if necessary.
Once in a year at the start of the season, examine the product carefully and check if all the parts are well secured, mounting screws are tightened and
decorative screw caps are intact. Check carefully the parts of the structure to see if the plastic joints or wooden parts have any cracks in them that
may affect the structural integrity. Renew the colouring of the wooden parts with child-safe paints. You can obtain the original colour parameters by
contacting the distributor or the manufacturer.
Check the height of the swing seat and, if necessary, adjust it according to the assembly instructions.
Warning! This is a Main Installation Guide. Please follow these instructions for all attached modules and additions - to platform, swing,
etc. In case you are unsure or have questions, please contact the distributor or the manufacturer of the product. The colours of the
product you purchased may differ from the image.
1.
Wood is a natural, organic material and each wooden part is unique with
its branches, cracks and colour varieties. Wooden materials may change its size
depending on the fluctuations of temperature and humidity. They will shrink
in warm and dry weather but they may expand in humid weather. As these
changes usually occur unevenly in all the wooden parts, the forces mentioned
may create cracks and splits. Likewise, due to the influence of the weather and
the atmosphere, the wooden parts may fade, change their colour or resin stains
may appear on them, they may also warp or bend. All the characteristics of
the wooden parts listed above are natural and predictable which is why their
appearing on the product does not make the product defective.
2.
3.
Publicidad
