Publicidad
Idiomas disponibles
Idiomas disponibles
SAFETY INFORMATION
WARNING
To reduce the risk of fire, electrical shock, product damage or personal injury, please follow
the safety instructions described in the user manual.
Read the user's manual before using the meter. lf the equipment is used in a manner not
specified by the manufacture , the protection provided by the equipment may be impaired.
This meter is designed and manufactured according to safety requirements of EN61010-
1, EN61010-2-030, EN61010-2-033, EN61010-031 concerning electronic measuring
instruments with a measurement CAT III 600V and pollution degree 2 and safety requirements
for electrical measurement and test. Follow all safety instructions to ensure safe use of the
instrument. Following these guidelines will yield many years of satisfactory service.
Preparing for use
• During use, observe all standard safety rules:
- Use protection to prevent electric shock.
- Do not misuse the instrument.
• Check the meter to see if there was any damage during transit
• Check test leads for cracks or breaks in the insulation on the wires
• lf the test leads need to be re placed, rneter's safety can only be guaranteed with similar
spec leads.
During use
• Always make sure the rotary switch is at the correct function and range.
• Do not exceed the protection limit values indicated for each function.
• Do not touch test lead tips while connected to a measurement circuit.
• n manual range if the value to be measured is unknown, select the highest range first and
lower as needed.
• Do not measure voltages that may exceed 600V between the terminals and ground.
• Always be careful when working with voltages above 60V DC or 30V AC RMS. Keep
fingers behind the probe barriers while measuring
• Never connect the meter leads a cross a voltage source while the rotary switch is in the
resistance, diode or continuity mode. Doing so can damage the meter.
• Do not perform resistance, diode and continuity measurements on powered circuits.
• Disconnect the test leads from the circuit before changing functions on the rotary switch.
• Do not place the meter in an environment with high pressure/temperature, dust, explosive
gas or vapor.
• Stop using the meter if any abnormalities or failures occur.
• Do not connect the test leads to a circuit without the battery securely fastened.
• Do not store the meter in an area of direct sunlight, high temperature or high humidity.
MAINTENANCE
• Repairs should only be implemented by trained personnel.
• Remove test leads from measurement circuits before opening the battery cover.
• In order to avoid incorrect readings that may cause damage or personal injury, replace
batteries as soon as the
symbol appears.
• Use a damp cloth and mild detergent to clean the meter.Do not use abrasives or solvents.
• Move the rotary switch to the OFF position when the meter is not in use.
• Remove the batteries if the meter is not going to be used for an extended period of time.
WARNING
To prevent electric shock and damage to the meter or personal injury, remove test lead
before opening battery cover.
Replacing the Batteries
• When the
symbol appears, it indicates the batteries need to be replaced.
• Unscrew the battery cover and remove it from the meter.
• Replace the used batteries with new AAA batteries.
• Replace the battery cover and secure it to the meter.
WARNING
Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or
rechargeable (ni-cad, ni-mh, etc) batteries.
Replacing the Test Lead (or alligator clip)
lf the test lead's insulation is damaged or has any wires exposed, the leads need to be replaced.
WARNING
Use meet EN 61010-031 standard, rated CAT III 600V, or better test leads.
ACCESSORIES
• Test Lead, CAT. III 600V 10A, 1 un.
• Alligator clip, 600V, 10A, 2 un.
• Batteries 1,5V, AA, 2 un.
• Summary instruction manual
ENG
ENGLISH
instruction manual:
APAC: MGL GLOBAL SOLUTIONS LTD
info.apac@mgl-intl.com
Flat 4-1, 4/F, No. 35, Section 3 Minquan
East Road. Taipei, Taiwan.
Tel: +886 2-2508-0877
EMEA: MGL EUMAN S.L.
info.emea@mgl-intl.com
Parque Empresarial Argame, 33163
Morcín. Asturias, Spain.
Tel: +34 985-08-18-70
Digital multimeter
See the full
AMERICAS: MGL AMERICA, LLC.
info.na@mgl-intl.com
US East Coast: 2810 Coliseum Centre
Drive, Ste. 100. Charlotte, North Carolina,
28217 USA
MGL EUMAN, S.L.
Tel: +1 833 533-5899
Parque Empresarial de Argame,
US West Coast: 760 Challenger Street.
C/Picu Castiellu, Parcelas i-1 a i-4
Brea, California 92821 USA
E-33163 Argame, Morcín
Tel: +1 310-728-6220
Asturias, España, (Spain)
www.mgl-intl.com
ENG
Publicidad
