Husqvarna ROYAL 43 Manual Del Operador página 12

IMPORTANT
Release the Operator Presence Control, to stop the engine, wait until the blade has stopped and
disconnect the spark plug lead:-
- before clearing a blockage;
- before checking, cleaning or working on the appliance
IMPORTANT
Never use water for cleaning your lawnmower. Do
not clean with chemical, including petrol, or solvents
- some can destroy critical plastic parts.
Cleaning
• Disconnect the spark plug lead.
• Turn machine on it's side with the exhaust uppermost.
1. Remove grass from under the deck with a
brush.(L1 and L2)
2. Using a soft brush - remove grass clippings from
the engine air intakes and exhaust (L3), cutting
height adjustment area, around the wheels (L4)
and the grass collector.
3. Wipe over the surface of your lawnmower with a
dry cloth.
L1
L3
Cutting System
Removing the Blade
• Disconnect the spark plug
lead.
• Turn machine on it's side
with the exhaust uppermost.
1. Use spanner to loosen
blade bolt by turning anti-
clockwise.(M)
2. Remove the blade bolt, blade and spacer washer.
3. Inspect for damage and clean as necessary.
Fitting the Blade
1. Fit the blade to the machine with the sharp
edges pointing away from the machine.
2. Re-assemble blade bolt through blade and
spacer washer.
3. Hold firmly and tighten blade bolt firmly with a
spanner. Do not over tighten.
IMPORTANT
Do not attempt any maintenance on your
lawnmower when the engine is hot.
Always handle the blade with care - sharp edges
could cause injury. USE GLOVES. Renew your metal
blade after 50 hours mowing or 2 years whichever is
the sooner - regardless of condition. If the blade is
cracked or damaged replace it with a new one.
ENGLISH - 7
All manuals and user guides at all-guides.com
MAINTENANCE
How to Charge the Battery (ROYAL 43SE)
1. Stop your lawnmower.
2. Disconnect the spark plug.
3. Remove the cap from
4. Plug charger lead into
5. Plug the battery charger
6. Charging will then commence.
7. Charge for 24 hours.
8. After charging, disconnect the charger from the
L2
9. Replace the cap on the charging point.(N)
10. The unit is now ready for use.
ENVIRONMENTAL INFORMATION
Electrolux Outdoor Products are manufactured under
an Environmental Management System (ISO 14001)
using, where practical, components manufactured in
the most environmentally responsible manner,
according to company procedures, and with the
L4
potential for recycling at the end of the products' life.
• Packaging is recyclable and plastic components
• Awareness of the environment must be
• If necessary, contact your local authority for
M
BATTERY DISPOSAL
• The battery should be taken to an Approved
• Do NOT dispose of used battery with
• Lead/Acid batteries can be harmful and
• Do NOT dispose of battery to water.
• Do NOT incinerate
DISPOSAL OF FUELS AND LUBRICATING OILS
• Wear protective clothing when handling any
• Avoid contact with skin.
• Remove petrol and engine oil before transporting
• Contact your local authority for information of
• Do NOT dispose of used fuels/oils with
• Waste fuels/oils are harmful, but can be
• Do NOT dispose of used fuels/oils to water.
• Do NOT incinerate
the charging point at the
bottom of the wiring
loom.(N)
connection on battery
loom.(N)
into a domestic electric socket.
socket and charging point.(N)
have been labelled (where practical) for
categorised recycling.
considered when disposing of 'end-of-life' product.
disposal information.
Service Centre or your local Recycling Station.
household waste
should be disposed of through the
recognised recycling facility in accordance
with European Regulation
fuels and lubricants.
the product.
your nearest Recycling/Disposal Station.
household waste
recycled and should be disposed of through
the recognised facilities.
N
Wiring Loom
charging
point cap