Publicidad
PROGRAMMING FLOWCHART
Change
Master Code
1
*
1
2
Enter New
Master Code
Double
Single
Press 6 Digits
Wiegand
Wiegand
Master/Slave
Select Type of Wiegand
selection
0
*
1
2
1
2
Master
Slave
Wiegand
Wiegand
Wiegand
26bit
30bit
34bit
Direct Menu
exit
Entering Menu is always done with B 3sec. + 000000 if the Master Code is not changed.
Submenu 0 - Master/Slave Selection. 1(Master) when the keypad is connected with proximity reader DINMTPX. Default = 2(Slave)
Submenu 1 - Change Master Code. The Master Code must be 6 digits. After enrolling new Master Code the DINPAD-M automatically exits the Menu and
the new master code must be typed to enter the menu.
Submenu 2 - Select Type of Wiegand. With this the Keypad can be adjusted to send 4 different Wiegand Outputs. The Wiegand selected must be the same
as the controller's Wiegand Input where the DINPAD-M Keypad is being connected. Example: If you use a controller that recognizes Wiegand 34bit, then
enter the menu of DINPAD-M, press 2, then press 3.
Submenu 3 - Select Output Protocol. The Keypad can send the Code by different Protocols. Use "Single Wiegand" when connected to third party
controllers. When "Single Wiegand" is selected, what is typed on the Keypad the same will be sent as Wiegand Number. Use Double Wiegand when
connected to EWS, use Clock&Data when connected to controller with Clock&Data input, use Codix when connected to Vi200, EX5, EX7, INOX99 or
VKP99.
Submenu 4 - PIN Code Length. If "0" is selected, then any PIN Code with any length can be sent, but the PIN Code is typed with "A" for confirmation( ex.
123 + A). If 1 to 8 is selected the PIN Code length is determinated by the number selected.
Submenu 5 - Entry Mode. "Only PIN Code" is disabling the proximity and DINPAD-M+DINMTPX works as keypad only. "Only Card" is disabling the Keypad
and DINPAD-M+DINMTPX works as Proximity Reader. "Card and PIN Code" defines the double security, both the Card and PIN Code is required for the
Wiegand to be sent. "Card or PIN Code" enables normal operation.
Submenu 6 - Presets.
The Presets are set of preprogrammed parameters for easy programming.
6-1 "Wiegand 26bit Normal" -
6-2 "Wiegand 34bit Normal" -
6-3 "Wiegand 34bit EWS Mode" -
6-4 "Wiegand 26bit EWS Mode" -
6-5 "Codix" -
Presets 6-3 and 6-4 to be used always when DINPAD-M is connected to EWS firmware ver.2.42 or higher.
Submenu 7 - Site Code Length. Set the code length sent to Host. Default is "0". To be used only in specific cases.
Submenu 8 - Enter Site Code. Put the site code always in 5 digit format (ex. 00170).
Submenu 9 - Backlight. Turns ON/OFF the backlight.
Enter "Master Code" press and hold B 3 sec. + 000000
Select Output Protocol
3
3
6
7
4
5
Clock &
6-bit
4-bit
Codix
8-bit
Data
per key
per key
per key
2
3
4
5
6
7
Wiegand
Wiegand
Wiegand
Wiegand
37bit
40bit
42bit
58bit
Type: Wiegand 26bit; Output: Single Wiegand; PIN Length: 4 digits; Entry Mode: Card or PIN Code
Type: Wiegand 34bit; Output: Single Wiegand; PIN Length: 4 digits; Entry Mode: Card or PIN Code
Type: Wiegand 34bit; Output: Double Wiegand; PIN Length: 4 digits; Entry Mode: Card or PIN Code
Type: Wiegand 26bit; Output: Double Wiegand; PIN Length: 4 digits; Entry Mode: Card or PIN Code
Output: Codix; PIN Length: any length with "A" in the end; Entry Mode: Card or PIN Code
Validation OK?
Yes
1 small beep + 1 long beep + Orange LED is 'ON'
Presets
6
1
2
3
4
Wiegand
Wiegand
Wiegand
Wiegand
26bit
34bit
34bit
26bit
normal
normal
EWS
EWS
PIN Code Length
Entry Mode
4
*
0
1 - 8
1
for any length
for lengths
only PIN
with "A"
between
Code
in the end
1 to 8 digits
Press "A" to validate
and exit the menu
(orange LED OFF)
Error Beep
No
(3 short beeps)
Backlight, Buzzer, Parity
5
*
0
1
2
Backlight
Backlight
Buzzer
Codix
OFF
ON
OFF
Site Code Length
5
*
1
2
2
3
4
Site Code
Card and
Card or
only
No Site
between
PIN
PIN
Code
Card
0 to 15
Code
Code
9
*
*
3
4
5
Buzzer
Parity
Parity
ON
OFF
ON
Enter Site
Code
7
8
3
4
Site Code
Site Code
5 digits
between
between
0 to 255
0 to 65535
*
Default:
4
Publicidad
