Denon DVD-A1 Instrucciones De Operación página 18

ENGLISH
w When "DIGITAL OUT" is selected:
NORMAL (Factory default)
When playing DVDs recorded in Dolby Digital
or DTS, bitstream signals are output from the
digital audio output terminals. When playing
DVDs recorded in linear PCM or packed
PCM, linear PCM signals are output.
Select "NORMAL" when making digital
connections to an AV amplifier with built-in
Dolby Digital and DTS decoder.
PCM
When playing Dolby Digital/DTS bitstream
signals or DVDs recorded in linear PCM or
packed PCM, the signals are converted into
48 kHz/16-bit PCM (2-channel) signals and
output from the digital outputs. When playing
DVDs recorded in PCM, linear PCM signals
are output.
e When "LPCM (44.1 kHz / 48 kHz)" is selected:
OFF (Factory default)
When playing linear PCM or packed PCM DVDs
that are not copyright-protected, for 2-channel
PCM audio signals up to 96 kHz, linear PCM
signals are output as such without being
converted from the digital outputs. (176.2 kHz
and 192 kHz signals are converted to 88.2 kHz
and 96 kHz, respectively.)
PCM signals of 48 kHz/16 bits and lower are
output, regardless of whether they are copyright-
protected or not.
For DVDs containing multi-channel PCM signals,
5 the digital signals are down-mixed for output into
two channels, front left and right. (Only the front
left and right channels are output for sources for
which down-mixing is prohibited.)
When playing copyright-protected linear PCM
or packed PCM DVDs, in consideration of
copyrights, no digital signals are output for
sources exceeding 48 kHz/16 bits. When
playing such sources, either set to "ON" or
make analog connections. (See page 9.)
ON
Linear PCM and packed PCM signals are
converted to 44.1 kHz or 48 kHz and output.
(The PCM digital audio output signals are
converted to 48 kHz or less in consideration of
copyrights.) When making digital connections
to an AV amplifier that is not compatible with
96 kHz/88.2 kHz signals, set to "ON".
When playing DVDs recorded in linear PCM
or packed PCM and the unit is set to output
digital and analog audio
simultaneously, the analog audio output
signals are also converted to 48 kHz or
below, so we recommend setting to "OFF"
and also making analog connections.
r When "BASS ENHANCER (2 CHANNEL)" is
selected:
OFF (Factory default)
No sound is produced from the subwoofer.
ON
Sound is produced from the subwoofer.
In this case, set the subwoofer to "YES" at
the speaker settings.
18
AUD I O SE TUP
AUD I O CHANNE L
D I G I TAL OUT
L PCM (4 4 .1 kHz / 4 8 kH z)
BASS ENHANCE R(2 CHANNEL)
DENON L I NK
Remote control unit
E X I T SE TUP
ENTER
SE L ECT : DEC I S I ON : ENTER BUT TON
Remote control unit
AUD I O SE TUP
AUD I O CHANNE L
D I G I TAL OUT
L PCM (4 4 .1 kHz / 4 8 kH z)
BASS ENHANCE R(2 CHANNEL)
DENON L I NK
Remote control unit
E X I T SE TUP
ENTER
SE L ECT : DEC I S I ON : ENTER BUT TON
Remote control unit
signals
AUD I O SE TUP
AUD I O CHANNE L
D I G I TAL OUT
L PCM (4 4 .1 kHz / 4 8 kH z)
BASS ENHANCE R(2 CHANNEL)
Remote control unit DENON L I NK
E X I T SE TUP
ENTER
SE L ECT : DEC I S I ON : ENTER BUT TON
Remote control unit
t When "DENON LINK" is selected:
B
OFF (Factory default)
Digital audio signals are not output from the
NORMAL
5
DENON LINK terminal.
PCM
ON
Digital audio signals are output from the
DENON LINK terminal.
To exit the setup mode
Use the ª cursor button to select "EXIT SETUP", then press the ENTER button. It is also possible to quit
by pressing the SETUP button on the remote control unit.
B
OF F
ON
B
OF F
ON
B
AUD I O SE TUP
AUD I O CHANNE L
D I G I TAL OUT
L PCM (4 4 .1 kHz / 4 8 kH z)
BASS ENHANCER(2 CHANNEL)
DENON L I NK OF F
Remote control unit
ON
E X I T SE TUP
ENTER
SE L ECT : DEC I S I ON : ENTER BUT TON
Remote control unit