Menu Sequence Overview - Bühler technologies Pressotronik PT77 Guía Rápida

Pressotronik PT77

8 Menu Sequence Overview

Main menu Submenu 1
Configuration P__i Shortcut
or 60s no action:
Equipment configuration
Exit main/submenu
____
Display
____
Measurement display
____
Pressotronik Out 1
PrES
Pressure main menu
Settings menu OUT1
Out x
Settings menu OUTx
Analog Out1
Settings menu Analog 1
Exit
Exit menu level
Basic EF b. E F Reset
Basic ext. functions Factory preset
Set Error handling
Error handling
Set Unit Press
Pressure unit
Set Upper
Set max. pressure
reassign O1
Assignment Out 1
reassign O2
Assignment Out 1
Display Rate
Display rate
Turn
Installation direction
Lock Device
Keylock
Exit
Exit menu level
Diagnostic diA Journal Out
Diagnostics menu Log output
Max/Min Press
Max/Min memory
Set Journal Out
Output monitoring
Delay MM
Min/max delay
Exit
Exit menu level
E
Exit
Exit menu level
BX130003 ◦ 02/2021
Submenu 2 Submenu 3
+
____
out1 SP1 ____
FH1 F1. H i ____
Switching point 1
____
rP1
FL1 F1. L o ____
Switch-back point 1
____
EF 1 EF1 Delay SP 1
Extended functions Delay OUT1 On
Delay RP 1
Delay OUT1 Off
Set Out 1
Definition OUT1
Check Out 1
Functional test OUT1
LED Out 1
Function status LED1
Exit
Exit menu level
Exit E ____
Exit menu level
out_ ____ See menu structure Out1
Not applicable for version with
analogue output
____ ____
An1 Analog Max1
A1. H i
Maximum value assignment
____
Analog Min1 A1. L o
Minimum value assignment
Set A.Out1 ____
A. o u1
Output function
____
Check An1 C. A n1
Functional test Analog 1
____
Exit E
Exit menu level
E
rES
Err. h
P. u ni
P. H i
r. o u 1
r. o u 2
di5
turn
Loc
E
J. o ut
P. M M
SJ. o u
DP. M M
E
Settings and Display Menu
____
Switch
____
Change measurement display to show details for the unit
MBAR - PSI
MBAR available when max. pressure (P.Hi) <=10 bar
____
Selection menu ____
SP1 Switching point setting /
FI. H i Assigns a value to frequency 100 Hz (only OUT1 and OUT2)
0b - < P. H i >
Selection menu ____
____ rP1 Set switch-back point /
FI. L o Assigning a value to frequency 1 Hz (only OUT1 and OUT2)
0b - < P. H i >
dS1 ____ Selection menu ____
___
Amount of time the signal must be present for output OUT1 to trigger.
0 - 100 Setting range: 0...100 seconds (for frequency output without function)
____ Selection menu ____
dr1 ___
Amount of time the signal must be present for output OUT1 to switch back.
0 - 100 Setting range: 0...100 seconds (for frequency output without function)
Definition of switching characteristics for output 1:
____ ____
ou1 Selection menu
___
Hno Hnc Hysteresis function NO contact or NC contact
Hno - FM
Fno Fnc Window function NO contact or NC contact /
n. o P Normal switching output operation
____ ____
C. o u1 Selection menu
____
oFF
Switching output Off /
n. o p - on
on Switching output On /
____ Selection menu ____
LEd1 L=__
LED = output: follows switching output
L= o
L= o - L=-o
L=-o LED = -output: inverted to switching output
____
E
____
Selection menu
____ Sets the maximum analogue output signal to a defined value.
(Note: Max. – Min >= 10 % of the measuring range)
0b - < P. H i >
____
Selection menu
____
Sets the maximum analogue output signal to a defined value.
0b - < P. H i > (Note: Max. – Min >= 10 % of the measuring range)
____
Selection menu
_ _ Selecting the analogue output function:
i I 4...20 mA
i 1 - u 3
____
Selection menu
____ n. o P Analogue output normal mode /
HALF Output mean analogue value /
n. o P - Lo
Alternate menu for version with analogue output
Not applicable when ordered with 2 or more switching outputs
____
Confirm
___
Resets the device to factory configuration
no - YES
____ ____
Confirm ___
Disable/enable normal error handling and analysis
no - YES
Selecting the pressure unit displayed
____
Selection menu
___
The measuring range will automatically be adjusted.
MBAR- PSI
MBAR available when max. pressure (P.Hi) <=10 bar
Selection menu ____
____
Configures the maximum pressure for the connected sensor.
(Example: sensor maximum measuring range 100 bar)
0 - P. H i
Selection menu ____
____
Assign switching output Out1 to function pressure(temp/level) or as error signal
Err - PrES
____
Selection menu
___
Assign switching output Out2 to function pressure(temp/level) or as error signal
Err - Pres
____
Selection menu
____ Selecting the display refresh rate:
FASt - off FASt [fast], Medi [medium], SLo [slow],
Selection menu ____
___
Rotates the display 180°
no - YES
____
Selection menu
___
Activating the keylock by entering a numerical code > 0 Master code 287
0 - 999
____
Selection menu
____ Displays the last 6 alarms + delete function.
Jor I - --- Display: JorX
____
Selection menu Displays limits + delete function.
____
___; _ - --- Display: Value – time passed in hours/days; toggle values and time ▲▼
____
Selection menu
out_
Selecting the alarm output to be logged
Out1 - Out_
____
Selection menu ___
Amount of time the signal must be present before saving the maximum / minimum value.
Setting range: 0...100 seconds
0 - 100
MBAR BAR MPA PSI
FH1 Define maximum window limit
FL1 Set lower window limit
FM Frequency output 1-100 Hz
F1 Simulation 1 Hz
F100 Simulation 100 Hz
u 1 2...10 V u 2 0...10 V u 3 0...5 V
Hi Output maximum analogue value
Lo Minimum analogue value output
MBAR [mbar], BAR [bar], MPA
oFF [Display off]
X – time passed in hours/days; toggle alarms ▲▼
Bühler Technologies GmbH
[Mega Pascal], PSI[psi]
13