HoMedics enviraScape WEL-ART Manual De Instrucciones página 4

3. Ensure the light bulb is inside the MOSAIC GLOBE (A). Attach MOSAIC GLOBE to
FOUNTAIN TOP (B) by pressing the tube in the center of the MOSAIC GLOBE onto the
spout in the middle of the FOUNTAIN TOP . (Figure 4)
4. Fill FOUNTAIN BASE (F) with enough clean water to completely cover the WATER
PUMP (D). Use the Fill Line as a guide. (Figure 5).
5. Place FOUNTAIN TOP (B) on top of FOUNTAIN BASE (F), being sure that the notch is
lined up correctly. (Figure 6)
6. Cover FOUNTAIN TOP (B) with GLASS STONES (J). (Figure 7)
7. Attach the ADAPTER (I) to the POWER CORD (G).
8. Plug the cord into 120V household outlet. The fountain is controlled by an ON/OFF
SWITCH (H) located on the POWER CORD (G). If WATER PUMP (D) does not
operate, rotate in-line switch once to turn "ON" and once to turn "OFF".
NOTE:
Ensure that the POWER CORD loops below the electrical outlet to form a
"Drip Loop". This will prevent water from running down the POWER CORD into the
electrical outlet. (Figure 7)
9. Enjoy the soothing sound of water and the beauty of rotating artisan globe.
Figure 4
Notch
Figure 6
All manuals and user guides at all-guides.com
Figure 5
Fill
Line
Figure 7
Glass
Stones
Drip Loop
6
Figure 8
CAUTION:
All servicing
of this fountain
must be performed
by authorized
HoMedics service
personnel only.
Maintenance
• To clean the WATER PUMP (D):
Unplug from electrical outlet. Remove it from the base of the fountain. Use a small brush or stream
of water to remove any debris. (Figure 8)
• To keep water clean:
Periodically change water and clean the product according to the water condition. Keeping the
water clean prevents the water from becoming sticky and forming micro-organisms. We
recommend distilled water to prevent mineral build-up.
• To clean off hard water deposits on the FOUNTAIN BASE (F)or
MOSIAC GLOBE (A):
Soak in a mixture of vinegar and water to clean and remove any mineral build-up.
• Keep the water at an optimum level:
Add water periodically to keep water level at an optimum level and avoid shortening the life of the
WATER PUMP .
NOTE: Never let the WATER PUMP run dry, as this will shorten its life.
• Fountain Storage:
Unplug the fountain from the electrical outlet, empty the water, and store fountain in a dry, cool place.
• Changing the light bulb:
First unplug fountain and let bulb cool down. Remove the bulb cover by holding glass bulb cover
in dry hand and rubber neck with other hand. Slowly pull apart. Slight twisting may help to loosen.
Be gentle with bulb cover since it is glass. Never pull on cord. Next pull bulb straight out and
replace with new bulb, inserting prongs into the holes. Replace bulb cover securely.
Troubleshooting
• If the WATER PUMP (D) fails to operate, check the following:
Check the circuit breaker, or try a different outlet to make sure the WATER PUMP is getting
electrical power.
NOTE:
Always disconnect from electrical outlet before handling the WATER PUMP .
• If the WATER PUMP gurgles, spews, or "burps":
Check the water level to make sure the WATER PUMP has enough water to function.
• Maintaining a desired water level:
Check the water level daily the first week to measure the rate of evaporation.
Refill with water as needed.
• If water is splashing outside the fountain:
Adjust the flow control lever to a lower setting on the WATER PUMP . (Figure 1)
PVC Tubing
Inserts Here
Impeller Housing
Pump Inlet
Front Plate
Suction Feet
Flow
Control
Lever
7
Back Plate