Schlage MTB11 Manual Del Usuario

*xxxxxxx*
Support and Warranty
www.schlage.com/support
(877) 671-7011
xxxxxxx
+1 512-712-1316
MULLION READER
INSTALLATION INSTRUCTIONS
MODEL MTB11
1
Separate case from baseplate.
Baseplate
Case
2
Mark and drill holes.
NOTE: Drill and tap for mounting on metal surface. Use Z\," (3 mm) holes
for mounting on wood, or appropriate anchors for other surfaces.
Drill and tap 6-32
hole
Drill and tap 6-32
hole
1" (25 mm)
For Indoor/Outdoor Use
Mobile Enabled Multi-
MTB11 Technology Reader -
Mullion
Tools
• Phillips Screwdriver
• 6-32 Tap
• 1" (25 mm), Z\," (3 mm) Drill Bits
• T10 Security Torx™ Bit (Optional)
3
Wire the cable to the control module.
A power limited, class 2 UL 294 approved power supply must be used.
Voltage rating: 5V to 28V
Total length To power supply To panel
to power supply or (power & ground wires) (all other wires)
to panel
Power supply voltage
12 V 24 V
20 ft (6.1 m) 22 22 22
50 ft (15.2 m) 22 22 22
100 ft (30.5 m) 22 22 22
200 ft (61 m) 22 22 22
300 ft (91.5 m) 20 22 22
400 ft (121.9 m) 18 22 22
500 ft (152.4 m) 18 20 22
600 ft (182.9 m) 18 20 22
700 ft (213.4 m) 18 20 22
800 ft (243.8 m) 16 18 22
900 ft (274.32 m) 16 18 22
1000 ft (305.8 m) - 18 22
Currents
Voltage Avg. mA Max. mA
12 80 120
24 45 65
Cable Connections
Black Ground
Blue Unused
Brown Red LED Control
Gray* Tamper Out
Green Wiegand Data 0 / Data
Orange Green LED Control
Pink RS485-A/Y
Red Power In
Shield Shield Ground
Tan RS485-B/Z
White Wiegand Data 1 / Clock
Yellow Beeper Control
The max run for a 5V supply is 50 ft (15 m) with 18 AWG.
* Tamper Outputs are to be connected to a UL Burglary System.
4
Route cable through holes.
5
Install baseplate.
In case of alternative mounting
screws, only a #6 diameter Pan Head
Screw should be used.
6
Plug cable into case.
7
Install case.
8
Snap cover into place and install cover screw.
Tamper
Resistant
6-32 x Z\v"
Pin-in-Torx
button head, Use if
desired.
Regular
6-32 x Z\v"
Do not
over-tighten!
TEST/SET-UP
a
Power the reader.
The LED will light followed by a beeper tone. This indicates that the
reader is ready.
If LED and beeper do not respond, check cable connections.
b
Present a proper card or token programmed to operate the
reader.
LED Indicators
Green Card was read and
accepted
Red Card was read but not
accepted (does not indicate
faulty installation)
OSDP Secure is recommended panel communication standard.
RS485 connection shall not be used in S319 applications until a compatible S319 panel is identified with
RS485 communications.
ULC-S319 compliance is no longer valid when any add-on, expansion, memory, or other module
manufactured or supplied by the manufacturer or manufacturer's representative is used. ULC-S319 Listed
PSU must be used for Canadian installations.
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Changes or modifications to this equipment not expressly approved by Schlage could void the user's
authority to operate the equipment.
Industry Canada Statement:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device. This Class A digital
apparatus complies with Canadian ICES-003.