Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
CONNECTING
Please connect the electric soldering iron to the solder station.
Connect the plug of the electric iron lead (a diode plug with 5 conjunctions) into the electrical outlet on
the face of the soldering station.
Turn off the power supply switch to the 0 position, and inset the power supply plug of the soldering
station to the electrical jack whose voltage conforms with what is marked on the data plate. At this
time, the soldering station is ready for work.
OPERATION
To make soldering work perfect, you have to use the proper soldering rod and operate the soldering
station accurately. Electric soldering rod with colophony is advised to use.
In practice, alloy solder L-SN60PbCu2（German Industry Standard 8516 (60% tin (60/40 solder) is
mostly used. This solder has many soldering rod standards and 1mm soldering rod is advised to use
in electric.
1. Heat to working temperature (the soldering temperature regulated on the soldering station)
2. Put the soldering mouth which is cleaned and equably filmed with tin and the soldering rod
together on the soldering point. The soldering preparation will melt first to clean the surface of the
metal which needs soldering. Then the soldering tin melts so as to create relating conductive
connections. The soldering of electric components costs not more than 2 minutes. The well-
welded jointing point looks slick and lustrous after cooling. While the soldering point with bad
quality and many mistakes looks lusterless, uneven and easy to crack. The causes leading to
such result are as following: the improper solder is used or the soldering temperature is regulated
too high. Another familiar used last time and the higher line will display current temperature of the
electric iron.
3. The soldering temperature can be regulated from 150°C to 450°C in steps by means of two
regulating switches (up+/down-). The temperature will increase by100C every grade till the
demanded temperature is displayed.
4. It is also can push (200℃, 300℃, 400℃) button to set the value directly.
5. When the soldering temperature is regulated to a wanted number, the factual working temperature
will approach the set temperature gradually.
When the soldering station is turned off, the regulated temperature will be kept automatically. And
when you turn on the machine next time, this set temperature will be displayed automatically.
Once any malfunction happens for example the temperature sensor is damaged, or the connecting
lead between the electric iron and the soldering station is disconnected, the display will show
malfunction. Further, the piezoelectricity sensor inside will give out sound of alarm. In that situation,
shut down the machine immediately, switch off the power supply and look up possible cause resulting
in malfunction.
TEMPERATURE
Connect the soldering station to power and put the power supply switch to 1 position. The soldering
station now operates.
At this time the lower line on the screen will displayed a set temperature.
Push (up+) switch to increase the temperature.
Push (down-) switch to decrease the temperature.
Every time you press the switch, the temperature will be changed by 10°C.
If you press the switch continuously, the changing of regulating will go on.
MAINTENANCE
Only clean the soldering station with a dry soft cloth and a little bit of soft cleaner.
Please clean up the outer components after turning off the soldering station and cut off the power.
Renew a damaged fuse only with a same characterized, it is prohibited to use other characterized.
Do not open the soldering station. Maintenance and repair can only be done by trained personal with
strict training. Self-disassembly may result in the danger of electric shock.
SW-Stahl und Werkzeugvertriebs GmbH
L
e
v
e
k r
u
s
r e
t S
a r
s
s
e
6
5
D
4 -
2
8
9
7
R
e
m
s
c
h
e
d i
Tel. +49 (0) 2191 / 46438-0
F
ax +49 (0) 2191 / 46438-40
- E
M
a
: l i
n i
o f
@
s
w
s
a t
l h
d .
e
Publicidad
Tabla de contenido
