Black and Decker GH600 Manual De Instrucciones página 2

10
11
14
13
ASSEMBLY / ADJUSTMENT SET-UP
• WARNING: The guard must always be on the tool to protect the user.
NEVER OPERATE TOOL WITHOUT GUARD FIRMLY IN PLACE.
UNPLUG THE TOOL BEFORE ATTEMPTING TO ATTACH THE GUARD.
1. Insert the upper assembly into the lower assembly by lining up the groove in the upper
tube so that it slides into the lower. Both the motor housing and the handle housing
should be on the same side of the tube. Push the upper tube until it does not move any-
more. A slight tug in the opposite direction will tell you the unit is assembled. Slide the
collar nut down and tighten it securely (Figure 1, 1A).
2. Position the open center of the guard over the line feed head (Figure 2).
3. Hinge the guard on the hook located on the lower motor housing. Ensure the line is free,
and not tucked under the guard. Once hooked, lightly pull on the back edge of the guard
and push the guard down until the 3 latches snap into place on the motor housing.
(Figure 3)
4. The guard is not intended to be removed once installed.
5. Once the guard is installed, remove the covering from the line cut-off blade, located on the
edge of the guard.
6. Push the auxillary handle onto the upper tube. Insert the handle bolt through both holes
in the handle and thread the knob on the bolt as shown in figure 4. The auxiliary handle
can be adjusted along the tube. Simply loosen the knob and position the handle as
desired. Retighten knob to secure the auxiliary handle. (Figure 4A)
7. An extension cord retainer (figure 5) is built into the switch handle that prevents the cord
from coming unplugged. To use this feature, simply double the extension cord about 8
inches from the end, and insert it into the slot in the bottom of the handle area. Hook the
loop formed by doubling the cord over the tab. Gently tug on the cord to insure that it is
firmly retained in the trimmer's handle. Plug the receptacle end of the extension cord into
the plug blades in the trimmer.
OPERATING INSTRUCTIONS
• CAUTION: ALWAYS WEAR EYE PROTECTION
• CAUTION: Inspect area to be trimmed and remove any wire, cord, or string-like
objects which could become entangled in the rotating line or spool. Be particularly careful
to avoid any wire which might be bent outwardly into the path of the tool, such as barbs at
the base of a chain link fence.
• Angle unit as shown in Figure 6.
• With the unit on, slowly swing the trimmer side to side as shown in Figure 7.
• To convert for maintenance edging, unplug the unit from the power source. Gently pull the
wire edge guide down into place as shown in Figure 8 and 9. Push the black "For Edging"
button and rotate the lower motor housing 180°. The tool will lock in the edger position.
• To operate as a maintenance edger, position the trimmer above the surface as shown in
Figure 10.
• Return to the trimming position by unplugging the unit from the power source, pushing the
black "For Edging" button and rotating the lower motor housing back 180°. The tool will
lock in the trimmer position.
When using the tool put up the wire edge guide to the original position, out of the way.
CUTTING LINE
LINE FEEDING
Your trimmer uses .065 in. (1.65 mm) diameter, ROUND nylon line to cut grass and
weeds quickly and easily. During use, the tip of the nylon line will become frayed and
worn and the special self feeding line hub will automatically feed and trim a fresh length of
line. Cutting line will wear faster and require more feeding if the cutting or edging is done
along sidewalks or other abrasive surfaces or heavier weeds are being cut. The advanced
automatic line feeding mechanism senses when more cutting line is needed and feeds
and trims the correct length of line whenever its required. DO NOT BUMP unit on ground
in attempt to feed line or for any other purposes.
CLEARING JAMS AND TANGLED LINES
From time to time, especially when cutting thick or stalky weeds, the line feeding hub may
become clogged with sap or other material and the line will become jammed as a result.
To clear the jam, follow the steps listed below.
1. Unplug the trimmer.
2. Press the release tabs on the line hub cap, as shown in Figure 11 and remove the cap by
pulling it straight off.
3. Lift the spool of nylon line out of the hub and clear any broken line or cutting debris from
the spool area. (If you plan to replace the spool or rewind it, this is the place to do so,
otherwise, move on.)
4. Unwrap about one foot (30 cm) of line to ensure that it's undamaged. If it is OK rewind it
and insert the line end through the eyelet in the spool hub as shown in Figure 12. Pull
4 in. (10 cm) of the line through the hole and maintain tension while placing the spool
down into the hub with the arrow up, as shown in Figure 13.
5. Press the spool down GENTLY and rotate it until you feel it drop into place. (When in
place, the spool will turn a few degrees left and right freely). Take care to keep the line
from becoming trapped under the spool.
6. Snap the hub cap and spring back on, and power the tool on. In a few seconds or less
you'll hear the nylon line being cut automatically to the proper length.
SPOOL OR LINE REPLACEMENT (Use .065 in. diameter ROUND line only)
1. Perform steps 1 and 2 above.
2. Remove the spool from the tool and remove and discard all line on the spool.
3. Choose either OPTION 1 or OPTION 2 below for spool or line replacement.
4. Insert the line end through the eyelet in the spool hub, as shown in Figure 12. Pull the
line through the hole to maintain tension while placing the spool down into the hub, as
shown in Figure 13.
5. Press the spool down GENTLY and rotate it until you feel it drop into place. (When in
place, the spool will turn a few degrees left and right freely). Take care to keep the line
from becoming trapped under the spool.
6. Snap the hub cap and spring back on, and power the tool on. In a few seconds or less
you'll hear the nylon line being cut automatically to the proper length.
OPTION 1: ACCESSORY REPLACEMENT SPOOL
Use Black & Decker replacement spool Model No. AF-100.
OPTION 2: REWINDING SPOOL USING BULK LINE
Bulk line for your trimmer/edger is available at extra cost from your local dealer or
Black & Decker Service Center. To install bulk line, follow the steps below.
All manuals and user guides at all-guides.com
12
(Use .065 in. diameter ROUND line only)
1. Insert one end of the bulk line into the hole in the spool as shown in Figure 12 about
1/2 in. (12 mm).
2. Hold the line in the hole and pull the rest of the line through the slot in the spool, shown
in Figure 14.
3. Snugly and evenly wind the bulk line onto the spool in the direction of the arrow on the
spool until the line builds up to the notches in the spool rim. (Fig. 14) Do not overfill spool.
The spool holds 30 feet (10 m) of line.
MAINTENANCE
Be sure the tool is unplugged.
1. Keep the air intake slots (Figure 9) clean to avoid overheating.
2. Your trimmer line can dry out over time. To keep your line in top condition, store spare
pre-wound spools or bulk line in a plastic, sealable bag with a tablespoon of water.
3. Plastic parts may be cleaned by using a mild soap and a damp rag.
4. DO NOT immerse tool in water or squirt it with a hose. DO NOT allow any liquid to get
inside it.
5. Do not store the tool on or adjacent to fertilizers or chemicals.
6. DO NOT clean with a pressure washer.
7. The line cutter on the edge of the guard can dull over time. It is recommended you peri-
odically touch-up the sharpness of the blade with a file.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment should be performed by authorized service centers or other qualified service
organizations, always using identical replacement parts.
ACCESSORIES
Use Black & Decker replacement spool Model No. AF-100 and / or the cap and spring
replacement Model No. RC100.
Reload nylon line (either bulk or prewound replacement spool) as shown in this manual.
• USE ONLY .065 in. (1.65 mm) DIAMETER NYLON MONOFILAMENT LINE. Do not use
serrated or heavier gauge line, as they will overload the motor and cause overheating.
The unit only functions properly with 0.065 in. diameter nylon monofilament line. This line
is available at your local dealer or authorized service center.
• WARNING: The use of any accessory not recommended by Black & Decker for use
with this tool could be hazardous.
Service Information
Black & Decker offers a full network of company-owned and authorized service locations
throughout North America. All Black & Decker Service Centers are staffed with trained
personnel to provide customers with efficient and reliable power tool service. Whether you
need technical advice, repair, or genuine factory replacement parts, contact the
Black & Decker location nearest you. To find your local service location, refer to the yellow
page directory under "Tools—Electric" or call: 1-800-544-6986.
Full Two Year Warranty
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in
material or workmanship. The defective product will be replaced or repaired at no charge in
either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from
whom it was purchased (provided that the store is a participating retailer). Returns should be
made within the time period of the retailer's policy for exchanges (usually 30 to 90 days after
the sale). Proof of purchase may be required. Please check with the retailer for their specific
return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or
authorized Service Center for repair or replacement at our option. Proof of purchase may be
required. Black & Decker owned and authorized Service Centers are listed under
"Tools-Electric" in the yellow pages of the phone directory and available on our website
www.blackanddecker.com.
This warranty does not apply to accessories. This warranty gives you specific legal rights
and you may have other rights which vary from state to state. Should you have any
questions, contact the manager of your nearest Black & Decker Service Center.
Free warning label replacement: If your warning labels become illegible or are missing,
call 1-800-544-6986 for a free replacement.
Imported by
Black & Decker (U.S.)
Inc.,
701 E. Joppa Rd.
Towson, MD 21286
U.S.A.
MODE D'EMPLOI
C C C C O O O O U U U U P P P P E E E E - - - - B B B B
Modèles GH600, ST7200, ST7201
M '
M '
ERCI D A VOIR CHOISI
ERCI D A VOIR CHOISI
V .B
V .B
ISITEZ ISITEZ WWW WWW LACKAND LACKAND
POUR ENREGISTRER VOTRE
POUR ENREGISTRER VOTRE
AVANT DE RETOURNER CE PRODUIT POUR QUELQUE
RAISON QUE CE SOIT, COMPOSER LE
1-800-544-6986
AVANT D'APPELER, AYEZ EN MAIN LE N° DE CATALOGUE ET LE CODE DE DATE. DANS LA PLUPART
DES CAS, UN REPRÉSENTANT DE BLACK & DECKER PEUT RÉSOUDRE LE PROBLÈME PAR
TÉLÉPHONE. SI VOUS AVEZ UNE SUGGESTION OU UN COMMENTAIRE, APPELEZ-NOUS. VOS
IMPRESSIONS SONT CRUCIALES POUR BLACK & DECKER.
IMPORTANTS RENSEIGNEMENTS :
• Installer le dispositif de protection avant d'utiliser l'outil afin d'éviter de
surchauffer le moteur.
• N'utiliser que du fil ROND de 1,65 mm (0,065 po) de diamètre. Sinon, l'outil
ne fonctionnera pas correctement.
Ne pas cogner la tête du mécanisme d'alimentation contre le sol afin de ne
•
pas l'abîmer.
Incliner légèrement l'outil (de 5 à 10 degrés) durant la coupe d'une bordure.
•
Toujours utiliser le dispositif de retenue et le dispositif de verrouillage de la
•
rallonge.
CONSERVER LE PRÉSENT GUIDE À TITRE DE RÉFÉRENCE.
LIGNES DIRECTRICES EN MATIÈRE DE SÉCURITÉ - DÉFINITIONS
Il est important que vous lisiez et compreniez ce mode d'emploi. Les informations qu'il
contient concernent VOTRE SÉCURITÉ et visent à ÉVITER TOUT PROBLÈME. Les sym-
boles ci-dessous servent à vous aider à reconnaître cette information.
DANGER :
Indique une situation dangereuse imminente qui, si elle n'est pas évitée, causera
la mort ou des graves blessures.
AVERTISSEMENT : Indique une situation potentiellement dangereuse qui, si elle n'est pas
évitée, pourrait causer la mort ou de graves blessures.
MISE EN GARDE : Indique une situation potentiellement dangereuse qui, si elle n'est pas
évitée, pourrait causer des blessures mineures ou modérées.
See 'Tools-
Electric'
– Yellow Pages –
for Service &
Sales
O O O O R R R R D D D D U U U U R R R R E E E E
B & D !
B & D !
LACK ECKER
LACK ECKER
D . /N O
D . /N O
ECKER ECKER COM COM EW EW WNER WNER
. .
NOUVEAU PRODUIT
NOUVEAU PRODUIT