OttLite T57WGC Guia De Inicio Rapido

G
L
S
1
D
U
T
Diagram 1 / schéma 1 / diagrama 1
LED Crane Desk Lamp
T57WGC T57G5B-FFP T5751B-FFP
INS150230
K
J
F
E
N
H
D
C
A
B
PL-0064B
English
CONGRATULATIONS!
You've purchased the finest in natural lighting technology with
your new OttLite ® product.
PRODUCT REGISTRATION FORM
Please complete the enclosed Product Registration Form and
return it today by mail, or register online by going to:
OttLite.com/warranty
LAMP ASSEMBLY WITH BASE
WARNING: To prevent electrical shock, make sure the lamp is not
plugged in until fully assembled per instructions.
1. Make sure the lamp is not plugged in to an electrical outlet.
2. Remove all packing from the box and lay both lamp assembly
and base on a solid surface such as a table.
3. Lift lamp assembly by lower arm (E) section and fully insert
dowel (D) into the stem (C) on the top of base (A).
4. Insert lock screw (B) through the recessed hole located in stem
(C). Lock screw (B) can be tighten by hand turning clockwise
M
until snug. NOTE: A screwdriver can also be used to
tighten lock screw (B).
5. Connect power adapter input (O) into lamp cord connection (N).
6. Plug power adapter (M) into a standard household 120V AC outlet.
Note: Only use with supplied power adapter to avoid
damage or fire.
LAMP ASSEMBLY WITH CLAMP
WARNING: To prevent electrical shock, make sure the lamp is not
plugged in until fully assembled per instructions.
O
1. Remove lamp from packing for use on a horizontal table.
2. To use on standard table, mount clamp (T) on the preferred
edge of the table. NOTE: Make sure clamp is secured before
installing lamp into the clamp.
3. Grasp by lower body (E) and upper body (F) and insert dowel
(D) into clamp (T). See Diagram 1.
4. Insert lock screw (U) through the recessed hole located on the
back side of clamp (T). Lock screw (U) can be tighten by hand
turning clockwise until snug. NOTE: A screwdriver can also
be used to tighten lock screw (U).
5. Verify the lamp is secure before using.
6. Plug the cord into a standard household 120V AC outlet.
SAFETY WARNING:
FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS
LAMP OPERATION
1. Turn the lamp ON or OFF by depressing switch (S) located on
the front-underside of the shade.
2. To reposition the light, hold the base steady and grasp either
lower arm (E) or upper arm (F) to position as desired. Lamp
body can also rotate on base.
CAUTION: The lamp is free to rotate on its base. DO NOT rotate
the lamp such that the power cord begins to wind up.
3. Shade (G) can rotate approximately 90 degrees left-right.
4. To increase tension in arm joints, twist selected knobs (H, K, L)
clockwise by hand. DO NOT force knobs as they can strip.
NOTE: The important safety instructions appearing in this
instruction sheet are not meant to cover all possible conditions
and situations that may occur. It must be understood that
common sense, caution, and care must be used with any
electrical product.
CAUTION!
THIS LUmINaIRE IS DamagED, IT SHaLL bE ExCLUSIvELY REPLaCED bY
THE maNUFaCTURER OR ITS SERvICE agENT OR a SImILaR qUaLIFIED
PERSON IN ORDER TO avOID a HazaRD. INDOOR USE ONLY.
FCC PART 15
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from
that of the receiver.
•
Consult the dealer or an experienced radio/TV technician
for help.
CAUTION! Any change or modification to product not expressly
recognized by OttLite Technologies voids OttLite's responsibility
for proper function of product.
CAN ICES-3 (B) / NMB-3 (B)
TO REDUCE THE RISK OF
AC/DC ADAPTER
Input: AC 100-240V, 50/60 Hz, 0.2A
Output: 21.0V DC, 0.28A with a Male DC Plug
LED Crane Desk Lamp
IF THE ExTERNaL FLExIbLE CabLE OR CORD OF
REV121415