OttLite 2LBWGC Guia De Inicio Rapido

A M
60˚
Diagram 1 / Schéma 1 / Diagrama 1
LED Light Box and Task Lamp Station
2LBWGC
INS150188
M
G
C
B
J
E
D
F
Diagram 2 / Schéma 2 / Diagrama 2 Diagram 3 / Schéma 3 / Diagrama 3
English
CONGRATULATIONS!
You've purchased the finest in natural lighting technology with your new
OttLite ® product.
M
PRODUCT REGISTRATION FORM
Please complete the enclosed Product Registration Form and return it today by
mail, or register online by going to:
www.warranty.ottlite.com
NOTE: THIS UNIT IS FULLY ASSEMBLED
H
Electrically-operated product. For use by ages 15 and up.
K
Setup and Operation
LED Light Box function
1. Remove all packing from LED Light box and place base (A) on a flat steady
M
surface.
2. Connect the AC Adapter input (B) into connector (C) in the rear-bottom of
the LED Light Box.
3. Plug the cord into a standard 120V AC outlet.
4. To "light-up" and use Light Box (D) do as follows:
• Turn "ON" switch (E);
• Lay design sheet on the screen (F);
• Lay drawing sheet on top;
• Trace object or scene outline lightly with pencil;
• Turn LED light of tracing pad "OFF" when not in use;
• Wipe any marks or dust off screen.
• NOTE: LED light has 3-levels of brightness; low, medium, high
LED Task Lamp function
1. To convert the LED Light Box into a Task Lamp follow diagram steps as
follows:
• Raise the LED Light Box (D) or lamp shade (D) from its rest
position by grasping and lifting as noted in Diagrams 1 & 2. Hold the
base steady as needed when raising the shade.
• While holding base (A) or body of lamp, firmly grasp shade (D),
raise until arms (G, H) are at the 90 degree angle, and flip shade
(D) forward as shown in Diagram 3.
• The LED Light Box is now converted into an LED Task Lamp.
2. Adjust the position of shade (D) by grasping the arms (G, H) to move them
into position; re-adjust shade as needed.
3. When applicable, adjust arm tension joints by using tool (J). Tension joints
are located at the top and bottom of arms (G, H). To properly adjust tension
joints, remove caps (M). DO NOT OVERTIGHTEN tension joint as it may
damage them.
4. Tool (J) is located in a hold cavity under compartment (K).
5. Remove compartment (K) to acquire tool (J). NOTE: After use of tool, store
in hold cavity. This is a special tool designed for use with this product.
6. To turn the lamp ON or OFF depress the switch (E) located in the front of
shade (D). NOTE: LED light has 3-levels of brightness; low, medium, high.
SAFETY WARNING:
90˚
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,
OR INJURY TO PERSONS ALWAYS FOLLOW BASIC SAFETY PRECAUTIONS, INCLUDING THE
FOLLOWING:
1. Read and understand all instructions before using.
2. DO NOT operate this equipment with a damaged power chord or if the unit
has been dropped or otherwise damaged, until a qualified electrician has
examined it.
3. Never use with an extension cord unless the plug can be fully inserted into
the receptacles in the extension cord.
4. If an extension cord is necessary, be sure it has a suitable current rating.
Cords rated for less amperage than this equipment may overheat. Be careful
to arrange the cord so that it will not be tripped over or pulled.
SL-8539
LED Light Box and Task Lamp Station
5. Do not alter the plug.
6. The lamp head included with this unit cannot be replaced by the consumer.
NOTE: The important safety instructions appearing in this instruction sheet
are not meant to cover all possible conditions and situations that may occur. It
must be understood that common sense, caution, and care must be used with
any electrical product.
Maintenance
1. The surface of LED Light Box is made of polycarbonate material and should
be treated with care.
2. Clean polycarbonate surface with a soft cloth and nonabrasive cleaner;
suggest a mix of mild soap and warm water.
3. Use a clean, new cloth made of soft material yet as lint-free as possible so it
does not trap small particles that might scratch the polycarbonate.
4. DO NOT wipe in a circular motion. Up and down uniform strokes only.
5. Never apply cleaner directly onto polycarbonate surface as it may seep
inside the unit.
CAUTION!
IF THE ExTERNAL FLExIBLE CABLE OR CORD OF THIS LUmINAIRE IS
DAmAGED, IT SHALL BE ExCLUSIvELY REPLACED BY THE mANUFACTURER OR ITS SERvICE
AGENT OR A SImILAR qUALIFIED PERSON IN ORDER TO AvOID A HAzARD. INDOOR USE ONLY.
FCC Part 15
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that the interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that of the receiver.
• Consult the dealer or an experienced radio/TV technician
for help.
CAUTION: Any change or modification to product not expressly recognized
by OttLite Technologies voids OttLite's responsibility for proper function of
product.
CAN ICES-3 (B) / NMB-3 (B)
AC/DC ADAPTER
Input: AC 100-240V, 50/60 Hz, 0.3A
Output: 12.5V DC, 600mA with a Male DC Plug
REV073015