Descargar Imprimir esta página

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 4

Enlaces rápidos

INSTALLATION, OPERATION AND DISASSEMBLY/
REASSEMBLY PROCEDURE FOR ANTI-CORROSIVE
CYLINDER SERIES 435 CONFORMING TO ISO 6431
FEATURES
Anti-corrosive type CIX cylinders are designed for use in
aggressive environments:
• Chemical, saline or humid atmospheres
• Food processing industries, such as dairy, cheese mak-
ing and meat processing environments: high resistance to
lactic acid.
STORAGE
The cylinder must be kept in its original packaging as long
as it is left unused. Do not remove the protective covers
from the ports.
STORAGE CONDITIONS
- protected from exposure to weather;
- temperature : -40°C to +80°C
- relative humidity: 95 %
After storage at low temperature, the cylinders must gradu-
ally be brought to room temperature prior to pressurisation.
OPERATING CHARACTERISTICS
• Air quality
- air or neutral gas ≤ 50 µm
- min. dew point: - 5°C
• Max. pressure: 10 bar.
Excess static pressure of 15 bar allowed once for 1 s.
• Fluid and ambient temperature: -10°C to +80°C
(with/without position detector)
• Position detector: PVC cable 0,3 m + stainless steel
screw-type external connector Ø M12, 3 pins, IP69K
(PNP), cat. no.: PNP-QDS-M12-F
• Lubricants
This type of cylinders can be operated with or without lubri-
cated air. However, once the cylinder is used in a lubricated
air circuit, lubrication must be maintained throughout the
cylinder's lifetime.
- Oil quality: non-detergent oil, without aggressive additives.
- The use of silicone-based lubricants is prohibited.
ELF
Spinelf 22 - Olna 22
LABO
Prima 32
MOBIL DTE light
SHELL Tellus S22
TOTAL Azzola 32 - ZS 32
ESSO
Spinesso 22
B.P.
HLP 22 ou 32
PUTTING INTO OPERATION
• The cylinders can be mounted in any position.
• These cylinders are NOT guiding units.
Any constraint on the rod will shorten their performance
and lifetime.
• Speed for optimum life: ≤ 1 m/s
• Max. allowable speed: 2 m/s (at 20°C)
• Adjustable pneumatic cushioning:
- Captive adjustable cushioning screws
CAUTION
Cumulating aggressive operational conditions, such as
max. pressure, min. temperature, will diminish the products'
performance.
NS
CLEANING
CIX type cylinders are designed to withstand high-pressure
wash-downs and bactericidal additives. Metal brushes or
objects that may impair the surface fi nish of the cylinders
(Ra = 0,6) must not be used for cleaning.
MAINTENANCE
WEARING PARTS
(Z1)
Disassembly
1- Unscrew the front and rear covers.
2- Remove the rod/piston unit from the cylinder barrel.
(Be sure to note the mounting direction of each
seal)
3- Carefully remove the lip seals (5).
4- Remove all other seals from the covers (1),(2),(3) and (4).
5- Clean the rod, piston, the inside of the barrel and all seal
grooves (do not use corrosive agents or solvents).
6- Do not disassemble the piston.
Reassembly
For best results, it is recommended to use grease spe-
cifi cally designed for lubrication in the food industry.
1- Lightly coat the lip seals and the piston grooves with
grease.
2- Insert the lip seal into the piston groove (fi g. A).
Observe correct mounting direction.
3- Insert the seal with a circular movement using a fl at tool.
(fi g. B)
4- Check the correct position of the seal (fi g. C).
5- Assemble the 2nd seal by repeating points 2,3 and 4.
Observe correct mounting direction (see fi g. D).
6- Lightly coat the outside and inside of the piston (*) and the
entry of the barrel with grease.
7- Place the piston diagonally into the bottom part of the bar-
rel (fi g. E).
8- When inserting the piston into the barrel, take care not to
damage the lip seals with the internal threads on the ends
of the barrel.
9- Use a fl at tool to push the lip seal with a circular
movement into the cylinder (Fig. F). Do not use a
screwdriver.
10- Place the piston back into the barrel (fi g. G).
11- Lightly coat the seals, scraper (1), rod seal (2), O-rings
(4), cushioning seals (3) and their grooves in the covers
with grease.
12- Place seals (1), (2), (3) and (4) into their respective
grooves and observe correct mounting direction.
13- Check the external threads on the covers and the inter-
nal threads on the barrel for cleanliness (including lack of
grease).
14- Lightly coat the external threads on each cover with Loc-
tite 542® and screw the covers by hand into the barrel
until they reach their mechanical stop.
2
INSTALLATION, OPERATION AND DISASSEMBLY/
GB
REASSEMBLY PROCEDURE FOR ANTI-CORROSIVE
CYLINDER SERIES 435 CONFORMING TO ISO 6431
REPLACEMENT OF CARTRIDGE SEALS (SCRAPER
AND ROD SEAL) USING OPTION KIT "CSR" (Z2) FOR
CYLINDER TYPE CIX
Disassembly
1- Unscrew the cartridge from the front cover and remove it
from the rod (be sure to note the mounting direction
of each seal).
2- Remove the seals and clean the cartridge (do not use
corrosive agents or solvents).
Reassembly
For best results, it is recommended to use grease specifi -
cally designed for lubrication in the food industry.
1- Lightly coat the seals, scraper (1), rod seal (2), O-ring (3)
and their grooves in the cartridge with grease.
2- Place seals (1), (2), (3) and (4) into their respective
grooves and observe correct mounting direction.
3- Check the external threads on the cartridge and the front
cover for cleanliness (including lack of grease).
4- Lightly coat the external thread on the cartridge with Loc-
tite 542® and screw the cartridge by hand into the front
cover.
REPLACEMENT OF CARTRIDGE SEALS (SCRAPER)
USING OPTION KIT "CSS" OR "PTF" (Z3) FOR CYLIN-
DER TYPE CIX
Disassembly
1- Unscrew the cartridge from the front cover and remove it
from the rod (be sure to note the mounting direction
of each seal).
2- Remove the scraper and clean the cartridge (do not use
corrosive agents or solvents).
Reassembly
For best results, it is recommended to use grease specifi -
cally designed for lubrication in the food industry.
1- Lightly coat the scraper (1) and its groove in the cartridge
with grease.
2- Place the scraper (1) it its groove and observe correct
mounting direction.
3- Check the external thread on the cartridge and the front
cover for cleanliness (including lack of grease).
4- Light coat the external threads on the front cover with
Loctite 542® and screw the cartridge by hand into the
cover until it reaches its mechanical stop.
3835107
NS
3
GB
3835107

Publicidad

loading

Resumen de contenidos para Asco Numatics 435 Serie

  • Página 1 INSTALLATION, OPERATION AND DISASSEMBLY/ INSTALLATION, OPERATION AND DISASSEMBLY/ REASSEMBLY PROCEDURE FOR ANTI-CORROSIVE REASSEMBLY PROCEDURE FOR ANTI-CORROSIVE CYLINDER SERIES 435 CONFORMING TO ISO 6431 CYLINDER SERIES 435 CONFORMING TO ISO 6431 FEATURES CLEANING REPLACEMENT OF CARTRIDGE SEALS (SCRAPER Anti-corrosive type CIX cylinders are designed for use in CIX type cylinders are designed to withstand high-pressure AND ROD SEAL) USING OPTION KIT “CSR”...
  • Página 2 MISE EN SERVICE, CONSEILS D'UTILISATION ET PROCEDURE MISE EN SERVICE, CONSEILS D'UTILISATION ET PROCEDURE DE DEMONTAGE-REMONTAGE VÉRINS ANTICORROSION, DE DEMONTAGE-REMONTAGE VÉRINS ANTICORROSION, SERIE 435, CONFORMES ISO 6431 SERIE 435, CONFORMES ISO 6431 NETTOYAGE PROCEDURE POUR REMPLACEMENT DES JOINTS PRESENTATION Les vérins CIX sont prévus pour résister aux lavages haute DE CARTOUCHE (RACLEUR ET JOINT DE TIGE) POUR Les vérins anticorrosion CIX sont adaptés à...
  • Página 3 INBETRIEBNAHME-, WARTUNGS- UND MONTAGEANLEITUNG INBETRIEBNAHME-, WARTUNGS- UND MONTAGEANLEITUNG FÜR KORROSIONSBESTÄNDIGE ZYLINDER, TYP 435, FÜR KORROSIONSBESTÄNDIGE ZYLINDER, TYP 435, NACH ISO 6431 NACH ISO 6431 MERKMALE REINIGUNG AUSTAUSCH DER CARTRIDGE-DICHTUNGEN (AB- Die korrosionsbeständigen Zylinder, Typ CIX, sind für den Der Zylindertyp CIX ist widerstandsfähig gegen Hochdruck- STREIFERDICHTUNG UND KOLBENSTANGENDICH- Einsatz im aggressiven Milieu geeignet: reinigung und antibakterielle Mittel.
  • Página 4: Limpieza

    PUESTA EN MARCHA, CONSEJOS DE UTILIZACIÓN Y PUESTA EN MARCHA, CONSEJOS DE UTILIZACIÓN Y PROCEDIMIENTO DE DESMONTAJE-MONTAJE CILINDROS PROCEDIMIENTO DE DESMONTAJE-MONTAJE CILINDROS ANTICORROSIÓN, SERIE 435, CONFORME ISO 6431 ANTICORROSIÓN, SERIE 435, CONFORME ISO 6431 PRESENTACIÓN LIMPIEZA PROCEDIMIENTO PARA SUSTITUCIÓN DE LAS Los cilindros anticorrosión CIX son adecuados para su utili- Los cilindros CIX están previstos para resistir a los lavados JUNTAS DEL CARTUCHO (RASCADOR Y JUNTA DE...
  • Página 5 ISTRUZIONI DI INSTALLAZIONE, UTILIZZO E SMONTAGGIO/ ISTRUZIONI DI INSTALLAZIONE, UTILIZZO E SMONTAGGIO/ RIMONTAGGIO DEI CILINDRI ANTICORROSIONE SERIE 435 RIMONTAGGIO DEI CILINDRI ANTICORROSIONE SERIE 435 CONFORMI ALLE NORME ISO 6431 CONFORMI ALLE NORME ISO 6431 DESCRIZIONE PULIZIA SOSTITUZIONE DELLA CARTUCCIA GUARNIZIONI I cilindri anticorrosione tipo CIX sono indicati per utilizzo in I cilindri CIX sono previsti per resistere ai lavaggi ad alta (RASCHIASTELO E GUARNIZIONE DELLO STELO)
  • Página 6 PROCEDURE VAN INSTALLATIE, BEDIENING EN PROCEDURE VAN INSTALLATIE, BEDIENING EN DEMONTAGE/HERMONTAGE VAN ROESTWERENDE DEMONTAGE/HERMONTAGE VAN ROESTWERENDE CILINDER SERIE 435 CONFORM ISO 6431 CILINDER SERIE 435 CONFORM ISO 6431 EIGENSCHAPPEN REINIGING PATROONAFDICHTINGEN (SCHRAPER EN Anti-corrosie CIX cilinders zijn ontworpen Cilinders van het type CIX zijn ontworpen om bestand te STAAFAFDICHTING) VERVANGEN M.B.V.
  • Página 7 COLOCAÇÃO EM SERVIÇO, CONSELHOS DE UTILIZAÇÃO E COLOCAÇÃO EM SERVIÇO, CONSELHOS DE UTILIZAÇÃO E PROCEDIMENTO DE DESMONTAGEM-MONTAGEM CILINDROS PROCEDIMENTO DE DESMONTAGEM-MONTAGEM CILINDROS ANTICORROSÃO, SÉRIE 435, CONFORME ISO 6431 ANTICORROSÃO, SÉRIE 435, CONFORME ISO 6431 CARACTERÍSTICAS LIMPEZA PROCEDIMENTO PARA SUSBTITUIR AS JUNTAS DE Os cilindros anticorrosão CIX estão adaptados à...
  • Página 8 МОНТАЖ, ЭКСПЛУАТАЦИЯ И ПРОЦЕДУРА ДЕМОНТАЖА/ МОНТАЖ, ЭКСПЛУАТАЦИЯ И ПРОЦЕДУРА ДЕМОНТАЖА/ ПОВТОРНОГО МОНТАЖА ДЛЯ АНТИКОРРОЗИЙНОГО ПОВТОРНОГО МОНТАЖА ДЛЯ АНТИКОРРОЗИЙНОГО ЦИЛИНДРА СЕРИИ 435 В СООТВЕТСТВИИ С ISO 6431 ЦИЛИНДРА СЕРИИ 435 В СООТВЕТСТВИИ С ISO 6431 КОНСТРУКТИВНЫЕ ОСОБЕННОСТИ ОЧИСТКА ЗАМЕНА КАРТРИДЖНЫХ УПЛОТНЕНИЙ Антикоррозийные...
  • Página 9 63 mm 97803071 97800082 97803088 97803093 N199-1046 80 mm 97803072 97800083 97803089 97803094 ASCO JOUCOMATIC SA 32 Av. Albert 1 - BP 312 - 92506 RUEIL Cedex - France 3835107 3835107 Tel. (33) 147.14.32.00 - Fax (33) 147.08.53.85 - http://www.asconumatics.eu...
  • Página 10 3835107 3835107...