Technical Service - EDM Product 08681 Manual De Instrucciones

• Maintain power tools. Check that moving parts are not misaligned
or stuck, that there are no broken parts, or other conditions
that may affect the performance of power tools. Power tools are
repaired before use, when they are damaged. Many accidents are
caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting
tools with sharp edges are less prone to binding and easier to
control.
• Use the power tool, accessories and tool tips, etc. in accordance
with these instructions and taking into account the working
conditions and the work to be carried out. Using the power tool for
applications other than those intended could cause a hazardous
situation.

TECHNICAL SERVICE

• Have your power tool checked by a qualified repair service using
only identical replacement parts. This will ensure that the safety
of the power tool is maintained.
TOOL USE AND CARE
• The appliance is designed exclusively for private outdoor use or
commercial use. Keep away from heat, direct sunlight, moisture
and rain, frost, and sharp edges.
• Do not allow persons not trained in the use of a high pressure
washer or without first reading the instruction manual to operate
the machine.
• High pressure cleaners should not be used by children or
untrained personnel.
• Children must be supervised to ensure that they do not play with
the appliance.
• Before starting your machine, check carefully for defects. If you
find any, do not start your machine and contact your local dealer.
• Check especially that the insulation of the electric cable must be
flawless and without cracks. If the power cord is damaged, a local
authorized service center should replace it.
Fire danger! Avoid shorting the contacts of a disconnected
battery. Do not incinerate the battery.
WARNING: Do not use the appliance close to human reach
unless they are wearing protective clothing.
• Do not direct the jet at yourself or others to clean clothing or
shoes.
• Hold the spray lance firmly with both hands.
• The operator and anyone in the immediate vicinity of the cleanup
site must take steps to avoid being struck by loose debris during
operation.
• Wear goggles and protective clothing during operation.
Instruction manual
▶1,0 mm2 máx. 12,5 m
▶1,5 mm2 máx. 20 m
▶1,5 mm2 máx. 20 m
CONNECTION TO THE ELECTRIC GRID
WARNING: This appliance has been designed for use
with the cleaning agent supplied or recommended by
the manufacturer. The use of other cleaning agents
or chemicals may adversely affect the safety of the
appliance.
• Disconnect from the power source before performing maintenance.
• To ensure the safety of the appliance, use only original
manufacturer or manufacturer-approved replacement parts.
• Do not use the appliance if a power cord or important parts of
the appliance are damaged, eg: safety device, high pressure hose
and trigger.
• Do not use the appliance with wet hands. If the appliance is damp
or wet, unplug it immediately. Do not put it in water.
• Tires and their valves can be damaged by the high pressure jet and
then explode.
• Never use the machine in an environment where there may be a
danger of explosion.
• It is not allowed to clean surfaces containing asbestos with high
pressure.
• This high pressure washer should not be used at temperatures
below 0 ° C.
WARNING: High pressure hoses, fittings and couplings are
important for the safety of the appliance. Use only hoses,
fittings and couplings recommended by the manufacturer.
WARNING: Improper extension cords can be dangerous.
The cables on the reels should always be fully unwound to
prevent the cable from overheating.
• If an extension cord is used, the plugs must be waterproof
and meet the requirements listed below for cord length and
dimensions:
• If the power cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified person
to avoid hazards.
• The following must be observed when connecting the high-
pressure washer to the electrical installation:
• The electrical supply connection must be made by a qualified
electrician and comply with IEC 60364-1.
• It is recommended that the electrical supply to this appliance
include a residual current device that interrupts the supply if the
earth leakage current exceeds 30 mA for 30 ms.
08681
REF.
ES
PT
EN
FR