Descargar Imprimir esta página

Newtec STOP LITE Manual Del Usuario página 4

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 10
GB - INFORMATIVE NOTE
Please read this informative note through carefully prior to use and prior to any maintenance work. The purpose
p
of this information contained herein is to assist and direct the user in choosing and using the PPE. Neither the
manufacturer nor the distributor can be held liable for an incorrect use of the PPE. This informative note must be
kept for the duration of the PPE.
PPE Model: cod. 121181 - mod. STOP LITE
PPE FEATURES
The retractable-type fall arrester device is a PPE against falls and it complies with EN 360 standard.
Fall arrester can be used by only one person at a time.
PPE DESCRIPTION
- Energy Absorber with loop for attaching it to the anchor point;
- Swivel connecting ring;
- Webbing retractor with brake and energy dissipating mechanism;
- Working webbing 17 mm made of polyester / Technora
- Snap hook with swivel function.
ATTENTION: The fall arrester device can be equipped only with certified snap hooks (according to EN 362). The snap hook
must have a swivel function.
CAPTION
1 - Energy Absorber
2 - Swivel connecting ring
3 - Identity label
4 - Webbing retractor
5 - Webbing rope
6 - Swivel snap hook
Month and year
of next periodic
review (don't
use the device
after this date
without making
inspection).
Periodic review +
12 months from
first use date.
CE MARK
The CE mark means that this article is a Personal Protective Equipment conforming to the essential health and
safety requirements set forth in the Directive 89/686/EEC and has been certified by the Notified Body CETE
A
APAVE SUDEUROPE, BP193, 13322 MARSEILLE, FRANCE, n°0082. In addition, the manufacturer is subjected
to the control of finished product CE quality guarantee by the Notified Body CETE APAVE SUDEUROPE, BP193,
13322 MARSEILLE, FRANCE, n°0082.
MARKING IDENTIFICATION
1 - Model
2 - Article code
3 - European standards
4 - CE Mark
5 - N° of the inspecting Notified Body
6 - Read the informative note
7 - Month and year of manufacture
8 - Serial number
9 - Factory identification
10 - Distributor's Mark
PRE-USE INSPECTION
Before each use, a person who is going to use the PPE, has to execute a close visual examination of all components, in order
to check if some mechanical, chemical or thermal defects are present. The user has also to check the retractor functioning,
by pulling vigorously the working webbing. The webbing have to block it and after release, the retractor have to roll up again
the webbing. If some doubt arises about the good condition and the right functioning of the PPE, it has to be withdrawn from
use. Then the PPE must be sent to the device manufacturer or to his certified representative to carry out a detailed inspection
and the eventual repair.
fabric. Length: 2,4 m;
®
a
b
c
d
e
f
a
d
h
j
cod. 121181 - mod. STOP LITE
Use only a full
Range of operating
body harness
temperatures.
conform to EN 361.
Don't release
Inspect the device
rapidly unwinded
before each use.
cable.
Check locking
Don't repair the
operation before
device by yourself.
each use.
Don't use the
Store the device
device with
in a protected
damaged webbing.
place.
Maximal
Before use read
admissible
the informative
deflection of the
note
webbing from the
vertical line.
e
f
g
Attach the device to the
anchoring point using the
upper fastening loop of
the energy absorber.
The device is designed to
be used horizontally and
against falls over the Type
140kg
B edge.
Admissible weight
of the user.
140kg
b
c
i

Publicidad

loading

Este manual también es adecuado para:

121181