Newtec STOP LITE Manual Del Usuario página 6

- PPE shall not be used outside its limitations, or for any purpose other than that for which it is intended.
- PPE should be a personal issue item.
- Before use ensure about the compatibility of items of equipment assembled into a fall arrest system.
- Periodically check connecting and adjusting of the equipment components to avoid accidental loosening or disconnecting
of the components.
- It is forbidden to use combinations of PPE in which the safe function of any items is affected by or interferes with the safe
function of another.
- Before each use of PPE it is obligatory to carry out a pre-use check of the equipment, to ensure that it is in a serviceable
condition and operates correctly.
- During pre-use check it is necessary to inspect all elements of the equipment in respect of any damages, excessive wear,
corrosion, abrasion, cutting or incorrect acting, especially take into consideration: in full body harnesses and belts: buckles,
adjusting elements, attaching points, webbings, seams, loops; in energy absorbers: attaching loops, webbing, seams, con-
nectors; in textile lanyards or lifelines or guidelines: rope, loops, thimbles, connectors, adjusting element, splices; in steel
lanyards or lifelines or guidelines: cable, wires, clips, ferrules, loops, thimbles, connectors, adjusting elements; in retract-
able fall arresters: cable or webbing, retractor and brake proper acting, casing, energy absorber, connector; in guided type
fall arresters: body of the fall arrester, sliding function, locking gear acting, rivets and screws, connector, energy absorber;
in connectors: main body, rivets, gate, locking gear acting.
- During periodic inspections, check the legibility of the PPE marking.
- It is essential for the safety of the user that if the product is re-sold outside the original country of destination the reseller
shall provide instructions for use, for maintenance, for periodic examination and for repair in language of the country in
which the product is to be used.
- A full body harness conformed to EN 361 is the only acceptable body holding device that can be used in a fall arrest sys-
tem.
- There are many hazards that may affect the performance of the equipment and corresponding safety precautions that have
to be observed during equipment utilization, especially:- trailing or looping of lanyards or lifelines over sharp edges; any
defects like cutting, abrasion, corrosion; climatic exposure; pendulum falls; extremes of temperature; chemical reagents;
electrical conductivity.
- PPE can be cleaned without causing adverse effect on the materials in the manufacture of the equipment. For textile prod-
ucts use mild detergents for delicate fabrics, wash by hand or in a machine and rinse in water. Plastic parts can be cleaned
only with water. When the equipment becomes wet, either from being in use or when due cleaning, it shall be allowed to dry
naturally, and shall be kept away from direct heat. In metallic products some mechanic parts (spring, pin, hinge, etc.) can
be regularly slightly lubricated to ensure better operation. Other maintenance and cleaning procedures should be adhered
to detailed instructions stated in the manual of the equipment.
- PPE must be transported in its original package.
- PPE must be stored in their original packaging, in a well-ventilated place, protected from direct light, ultraviolet degrada-
tion, damp environment, sharp edges, extreme temperatures and corrosive substances.
- The PPE must be disposed of in compliance with the local regulations in force on this subject (dump, incinerator).
- In the case of manufacturing defects this PPE will be replaced.
It is the responsibility of the user organisation to provide the IDENTITY CARD and to fill in the details required. The identity
card should be filled in before the first use of the equipment. Any information about the protective equipment (device name,
serial number, date of purchase, date of first use, user's name, information about reviews and repairs) shall be noted in the
IDENTITY CARD. Do not use the PPE without the identity card duly filled in.
DEVICE NAME
SERIAL NUMBER
USER'S NAME
DATE OF PURCHASE
DATE INSPECTION REASON
1
2
3
4
5
IDENTITY CARD
TECHNICAL INSPECTIONS
For more information, contact:
Registered Community Trade Mark, no 001240407 c/o UAMI - Alicante - Spagna
www.newtecsafety.com - info@newtecsafety.com - Factory: PL8310001653
CODE
PRODUCTION DATE
DATE OF FIRST USE
DEFECTS NOTED, REPAIRS CARRIED OUT,
OTHER RELEVANT INFORMATION
cod. 121181 - mod. STOP LITE
PERIODIC REVIEW NEXT
DUE DATE
RESPONSIBLE
PERSON
SIGNATURE