Makita DWT310 Manual De Instrucciones página 5

ENGLISH (Original instructions)
SPECIFICATIONS
Model:
Bolt siz e
Max imum torq ue
No load speed ( R P M)
O v erall length
R ated v oltage
Net w eigh t
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
Specifications and battery cartridge may differ from country to country.
The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combinations, according to EPTA-Procedure 1/
Applicable battery cartridge and charger
Battery cartridge
C h arger
Some of the battery cartridges and chargers listed above may not be available depending on your region of
resi d en c e.
WARNING:
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or fire.
Intended use
The tool is intended for fastening tor-shear type high
tensile bolts.
Noise
The typical A-weighted noise level determined accord-
ing to EN 8 1- - :
S oun d pressure le v el ( L
S oun d po w er le v el ( L ) :
WA
Uncertainty (K) : dB(A)
NOTE: The declared noise emission value(s) has been
measure d in a c c or d an c e w it h a stan d ar d test met h o d
and may be used for comparing one tool with another.
NOTE: The declared noise emission value(s) may
also be used in a preliminary assessment of exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the po w er tool can differ from the declared
value(s) depending on the w ays in w hich the
tool is used especially w hat kind of w orkpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times w hen the tool is s w itched
off and w hen it is running idle in addition to the
trigger time).
) : 8 dB(A)
pA
dB (A)
1 , are shown in the table.
BL1815N / BL18 / BL18
BL18 B / BL185 / BL185 B / BL18
DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN
Work mode: screwdriving without impact
Vibration emission (a
Uncertainty (K) : 1.5 m/s
NOTE: The declared vibration total value(s) has been
measure d in a c c or d an c e w it h a stan d ar d test met h o d
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
WARNING:
The vibration emission during
actual use of the po w er tool can differ from the
declared value(s) depending on the w ays in w hich
the tool is used especially w hat kind of w orkpiece
is processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times w hen the tool is s w itched
off and w hen it is running idle in addition to the
trigger time).
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included as Annex A
to t h is instru c tion manual.
5 ENGLISH
DWT310
M1 6 , M20, M22
8 04 N• m
-1
1 4 min
29 6 mm
D .C . 36 V
6 .5 - 7.1 kg
B / BL18 / BL18 B / BL18
B
8 1- - :
2
) : .5 m/s or less
h
2
/