Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
FUNCTIONAL DESCRIPTION
CAUTION:
Al w ays be sure that the tool is
s w itched off and the battery cartridge is removed
before adjusting or checking function on the tool.
Installing or removing battery cartridge
CAUTION:
Al w ays s w itch off the tool before
installing or removing of the battery cartridge.
CAUTION:
Hold the tool and the battery car-
tridge firmly when installing or removing battery
cartridge. Failure to hold the tool and the battery
cartridge firmly may cause them to slip off your hands
and result in damage to the tool and battery cartridge
and a personal injury.
Fig.1: 1. R e d in d i c ator 2. Button 3. Battery cartridge
To remove the battery cartridge, slide it from the tool
while sliding the button on the front of the cartridge.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator on the
upper side of the button, it is not locked completely.
CAUTION:
Al w ays install the battery cartridge
fully until the red indicator cannot be seen. I f not,
it may accidentally fall out of the tool, causing injury to
you or someone around you.
CAUTION:
Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
Indicating the remaining battery capacity
Only for battery cartridges with the indicator
Fig.2: 1. I n d i c ator lamps 2. Check button
Press the check button on the battery cartridge to indi-
cate the remaining battery capacity. The indicator lamps
lig h t up f or a f e w se c on d s.
Indicator lamps
Lighted
Off
Remaining
capacity
Blinking
75 %
to 1 00%
5 0%
to 75 %
25 %
to 5 0%
0%
to 25 %
C h arge th e
battery.
The battery
may have
mal f un c tione d .
NOTE: D epen d ing on t h e c on d itions o f use an d t h e
ambient temperature, the indication may differ slightly
from the actual capacity.
Tool / battery protection system
The tool is equipped with a tool/battery protection sys-
tem. This system automatically cuts off power to the
motor to extend tool and battery life. The tool will auto-
matically stop during operation if the tool or battery is
placed under one of the following conditions:
Overload protection
When the tool or battery is operated in a manner that
causes it to draw an abnormally high current, the tool
automatically stops without any indication. In this sit-
uation, turn t h e tool o f f an d stop t h e appli c ation t h at
caused the tool to become overloaded. Then turn the
tool on to restart.
Overheat protection
When the tool or battery is overheated, the tool stops
automatically. In this case, let the tool and battery cool
before turning the tool on again.
Overdischarge protection
When the battery capacity is not enough, the tool stops
automatically. In this case, remove the battery from the
tool and charge the battery.
Sw itch action
WARNING:
Before installing the battery car-
tridge into the tool, al w ays check to see that the
s w itch trigger actuates properly and returns to
the " OFF " position w hen released.
To prevent the switch trigger from accidentally pulled,
the trigger-lock button is provided.
To start the tool, depress the trigger-lock button from
A side and pull the switch trigger. Release the switch
trigger to stop. After use, press in the trigger-lock button
f rom B si d e.
Fig.3: 1. Trigger-lock button 2. S w it c h trigger
NOTE: The tool automatically stops if you keep pull-
ing the switch trigger for about
When you pull the eject lever, the bolt tip is ejected from
t h e tool.
Fig.4: 1. Eject lever
Battery pow er lamp
When the remaining battery capacity becomes low,
the battery power lamp blinks. Charge the battery or
replace the battery with fully charged one. When the
remaining battery capacity becomes much lower, the
tool stops and the battery power lamp lights up.
Fig.5: 1. Battery power lamp
7 ENGLISH
minutes.
Publicidad
Tabla de contenido
