Publicidad
Idiomas disponibles
Idiomas disponibles
DE
Vor der
Funktions-
Montage
Montage
WICHTIG! Gewährleistungsbedingungen (bitte aufbewahren)!
48 Monate Gewährleistung auf die Funktionsfähigkeit unseres Gerätes 2 Lautsprecher Ultraschallgerät:
1.
Wir regulieren gerechtfertigte Beanstandungen innerhalb der Gewährleistungsfrist ab Erwerb kosten-
frei, nach unserer Wahl durch Reparatur oder Lieferung eines Ersatzproduktes. Voraussetzung ist, dass
unser Produkt ordnungsgemäß nach unserer Einbauanleitung eingebaut und gepflegt wurde.
2.
Um uns eine Problembehebung zu ermöglichen, bitte das komplette Gerät inklusive Kabel sowie die
Einbaurechnung zunächst auf eigene Kosten an uns übersenden.
3.
Die Ein- und Ausbaukosten werden nur bei nachgewiesen mangelbehafteten Geräten übernommen.
Eine etwaige Haftung unsererseits nach § 5 unserer Allgemeinen Geschäftsbedingungen bleibt, bei
Vorliegen der dortigen Voraussetzungen, unberührt.
4.
Bei Schäden, die durch nicht sachgemäßen Einbau oder fehlerhafte, nachlässige oder gewaltsame Be-
dienung entstehen, erlischt der Gewährleistungsanspruch. Es besteht keine Haftung für Folgeschäden.
Technische Änderungen und Irrtümer vorbehalten.
Bitte für etwaige Gewährleistungsansprüche unbedingt ausfüllen: Gewährleistungsansprüche können nur
mit ausgefülltem Coupon und Werkstattrechnung bearbeitet werden!
Stempel der Werkstatt
Kaufdatum
Technik-Hotline
+49 (0) 7631 9727-80
Entwicklung und Vertrieb
Norbert Schaub GmbH
Robert-Koch-Straße 20
79395 Neuenburg am Rhein
GERMANY
Tel. +49 (0) 7631 9727- 0
Fax +49 (0) 7631 9727-27
service@stop-go.de
www.stop-go.de
6
Fehler-
Schaltplan
kontrolle
suche
Seriennummer des Gerätes
Contents
1.
1 x Ultrasonic device with 2 speakers
Gewähr-
leistung
Technical data
Operating voltage:
Power consumption:
Reverse polarity protection:
Fuse in the fuse holder:
Ultrasound frequency:
Dispersion radius:
Dispersion angle:
Sound pressure:
Function control light:
Moisture protection:
Please note before installing
1.
Once the device is switched on, it takes several seconds before ultrasound is emitted. As soon as
ultrasound is being emitted, the
2.
Never clean the unit using a high-pressure hose or steam blower!
Caution overvoltage protection!
When jump-starting, welding or quick-charging, please switch off the device!
Prior to
installation
Martens mark their territory with scent marks. Before fitting the device, the area to be protected – i.e. the
engine compartment, underbody and wheel housing – must be thoroughly cleaned. We recommend using our
STOP&GO odour remover (item code
All units are checked prior to being dispatched.
positive and negative battery cables directly to the car battery. When the device is operated for the first time,
red
the
function control LED should begin to blink within no more than 1 minute. If the function check is suc-
cessful but ultrasound is not emitted after installation, an installation error has occurred (see trouble shooting).
How the device works
This device uses ultrasound to repel martens from the engine compartment. Ultrasonic waves in the frequency
range of animal fear and warning cries signal extreme danger to the marten. The device features frequency
modulation in order to prevent habituation.
Prior to
installation
Please remove the fuse from the holder during installation. Install the
upper third of the engine compartment
they are protected from excessive heat, water and dirt. We recommend positioning the device so that the area
of diffusion is directed downwards from above. For clarification: Imagine the area of diffusion is the beam
of a torch, which needs to illuminate the largest area possible. We recommend using the optional mounting
bracket (item code 07599).
The positive battery cable with a fuse is connected to the unswitched terminal 30 or directly to a 12 V plus
connection (after or at the vehicle's fuse box) on the car battery. Connect the earth cable (–) to an original
earthing point on the vehicle body. The control line (green cable) must be connected to the plus ignition power
supply of the on-board power supply
car radio's Europlug. If the cable (terminal 15) is properly connected, the device will switch on automatically
as soon as the ignition is switched off.
Note: If you do not connect the cable (terminal 15), the device will remain permanently switched on. This does
not affect the operation of the device, but it is not recommended.
We recommend installing the device in the upper third of the engine compartment since martens, due to
their burrowing behaviour, instinctively make their way up through the engine cavity. Moreover, this facilitates
installation and ensures that all of the components are better protected from dirt.
12 V
approx. 25 mA (including after a short circuit)
is provided
0.5 A F
22–28 KHz, frequency modulation
360°
2 x 160°
approx. 105 dB
2 x red LEDs
shock and splashproof
red
function control LEDs will begin to blink.
Function
Trouble
Installation
check
shooting
07503). It is also advisable to neutralise the parking area by cleaning it.
Please check again before
Function
Trouble
Installation
check
shooting
so that the area of diffusion of the speakers is as large as possible and
(terminal
15). This terminal is located on the ignition switch or on the
EN
Circuit
Warranty
diagram
installing. To do this, connect the
Circuit
Warranty
diagram
speakers of the ultrasonic device in the
7
Publicidad
