Technical Data - EINHELL TC-CD 18-2 Li Manual De Instrucciones Original

Taladro atornillador con batería
Ocultar thumbs Ver también para TC-CD 18-2 Li:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 69

4. Technical data

Voltage supply ........................................18 V d.c.
Idling speed: ............................0-350/0-1250 rpm
Torque settings: ........................................... 18+1
Forward and reverse rotation ..........................yes
Chuck clamping width ....................... max. 10 mm
Battery charger output voltage: ............. 23 V d. c.
Battery charger output current: .................... 0,5 A
Mains voltage for charger ... 100-240 V ~ 50/60 Hz
Battery type: .......................................Lithium-ion
Number of battery cells: .................................... 5
Battery capacitance: ................................. 1.5 Ah
Weight.........................................................1.6 kg
Max. screw diameter: .................................. 6 mm
The maximum screw diameter indicates the ma-
ximum diameter of the screw that can be screwed
into wood. The screw diameter can vary depen-
ding on the type of wood.
Sound and vibration
Sound and vibration values were measured in
accordance with EN 62841.
L
sound pressure level ................... 70,88 dB(A)
pA
K
uncertainty ............................................. 3 dB
pA
L
sound power level ..................... 81,88 dB(A)
WA
K
uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 62841.
Drilling in metal
Vibration emission value a
K uncertainty = 1.5 m/s
Screwing without hammer action
Vibration emission value a
K uncertainty = 1.5 m/s
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
Anl_TC_CD_18_2_Li_SPK7.indb 16
Anl_TC_CD_18_2_Li_SPK7.indb 16
≤ 2.5 m/s
2
h
2
≤ 2.5 m/s
2
h
2
- 16 -
GB
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect wor-
king order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
Have the appliance serviced whenever ne-
cessary.
Switch the appliance off when it is not in use.
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
Limit the operating time.
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched off and times in which the tool is
switched on but operates without load).
04.12.2019 09:31:57
04.12.2019 09:31:57

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

45.138.20

Tabla de contenido