Assembling The Equipment; Fitting The Filters - EINHELL TE-VC 2025 SACL Manual Del Usuario

5.1 Assembling the equipment

Fitting the wheels (Fig. 4-11)
Place a split pin for fitting the wheels (31) through
the appropriate hole in the axle (33) and fit a
washer (30), a wheel (13) and a washer to the
axle (33) (Fig. 5-6). Now slide the axle (33)
through the guides provided for it on the undersi-
de of the tank (10) (Fig. 7). Fit a washer and the
second wheel (13) to the empty end of the axle
(33) and secure it with the other washer (30) and
the split pin (31) (Fig. 8-10). Push the covers (32)
on to the outside of the wheels (13) so that the
detents engage on the covers (32) for the wheel
(13). (Fig. 11).
Fitting the castors (Fig. 12)
Fit the castors (12) into the appropriate moun-
tings on the underside of the container (10). Push
the castors (12) firmly into the mounting until they
engage with a clicking noise (Fig. 12).
Fitting the equipment head (Fig. 14)
The equipment head (5) is fastened to the contai-
ner (10) by the carry-handle (18). To remove the
equipment head, swing the carry-handle forward
(Fig. 14) and lift off the equipment head. When
you fit the equipment head, make sure that the
carry-handle is in the correct position (Fig. 14).
Fitting the carry-handle (Fig. 15-15a)
Fit the carry-handle (18) in accordance with Fig.
15-15a.

5.2 Fitting the filters

Important!
Never use the wet and dry vacuum cleaner wit-
hout a filter.
Always ensure that the filters are securely seated.
Anl_TE_VC_2025_SACL_SPK8.indb 30 Anl_TE_VC_2025_SACL_SPK8.indb 30
GB
Fitting the foam filter (Fig. 16)
For wet-vacuuming, slip the supplied foamed
plastic filter (25) over the filter basket (Figs. 2/20).
The pleated filter (Fig. 3/24) already fitted upon
delivery is not suitable for wet-vacuuming!
Fitting the pleated filter (Fig. 17)
For dry-vacuuming, slip the pleated filter (Fig.
3/24) over the filter basket (Fig. 2/20). The pleated
filter (Fig. 3/24) is suitable for dry-vacuuming only.
5.3 Fitting the tank bag (Fig. 18)
Fit the dirt bag (Fig. 3/27) as shown in Figure 18.
5.4 Fitting the suction hose (Fig. 1-3; 18)
Connect the suction hose (9) to the correspon-
ding connector on the wet and dry vacuum clea-
ner, depending on the application required.
Vacuuming
Connect the suction hose (9) to the suction hose
connector (8).
Blowing
Connect the suction hose (9) to the blow connec-
tor (19).
Air regulator (Fig. 3)
The air regulator (29) can be fitted between the
suction hose (9) and the suction tube (17). The
suction power of the nozzle can be infinitely ad-
justed using the air regulator (29).
When wet vacuuming, make selective use of the
air regulator to suck in air as well as liquids. This
will help to take some strain off the equipment
when vacuuming liquids.
5.5 Suction nozzles
Combination nozzle (Fig. 3)
The dual-purpose nozzle (14) is for vacuuming
solids and liquids over medium to large areas.
Crevice nozzle (Fig. 3)
The crevice nozzle (23) is designed for vacu-
uming solids and liquids in corners, edges and
other areas that are difficult to access.
Upholstery nozzle (Fig. 3)
The upholstery nozzle (26) is specially designed
for vacuuming solids on upholstery and carpets.
- 30 -
30.11.2021 07:35:21 30.11.2021 07:35:21