Publicidad
2
ON
OFF
2
P1
3
10
9
F1
8
11
12
7
13
6
14
5
4
15
3
2
1
2
All manuals and user guides at all-guides.com
Spostare il dispositivo di bloccaggio come indicato
in fig. 2A. Sfilare il supporto in acciaio dal monitor e
fissarlo, ad un'altezza adatta all'utente, mediante
tasselli e viti in dotazione.
Rispettare l'indicazione ALTO e fare in modo che
l'uscita dei cavi dalla parete coincida con l'apposi-
to passaggio del supporto (fig. 3).
Svitare le due viti di fissaggio e togliere la parte
sinistra del mobile (fig. 4). Passare i conduttori
attraverso la feritoia sul fondo del monitor, posizio-
nare il monitor nel supporto da parete ed innestarlo
al supporto stesso con un movimento verso il basso
(fig. 5).
Per evitare cadute dal monitor a causa di urti acci-
dentali, bloccare il monitor stesso al supporto da
parete spostando verso destra (fig. 2B) il dispositi-
vo di bloccaggio.
Procedere nella maniera opposta in caso di smon-
taggio del monitor.
Effettuare i collegamenti e rimettere la parte sinistra
4
del mobile fissandola con le due viti.
GB INSTRUCTIONS FOR USE
AND INSTALLATION
WARNING FOR THE INSTALLER
1
These instructions should be attached to the
receiver.
VMF/100.01 FLAT MONITOR WITH HANDSET
It is equipped with the following controls and war-
nings, figure 1:
Thumb-wheel D to switch the monitor
ON/OFF and for the brightness control.
Button to bring the monitor live and manual
sequencing of any additional panel/camera.
5
Button to turn on stairs light.
Door lock release button.
•
Aux 1 - Button for auxiliary services as
required.
•
Aux 2 - Button for auxiliary services as
•
required.
LED 1 Green LED can be used to indicate an
external function.
LED 2 Yellow LED can be used to indicate an
external function.
LED 3 Red LED can be used to indicate an exter-
nal function.
Switches Aux 1 and Aux 2 are normally open, when
actuated the contacts close on –0V DC. Max. cur-
4
rent demand 100mA at 24V.
To activate LED 1 and LED 2 line 13 and 14 should
be connected via an external switch device which is
common to terminal 5 of the system, 0V DC.
The monitor is protected by the slow blow fuse F1 - T
500 mA - mounted on monitor's printed card, figures 6.
(Fuse: F = fast, T = slow).
WARNINGS FOR THE USER
- Please do not open or tamper the device (high
voltage!).
- Please avoid knocking or bumping the apparatus
as it could result in the breakage of the picture tube
and the consequent projection of glass fragments.
- In the case of breakdown or modification of the
apparatus of the system (such as power supplier ...)
please contact a specialized maintenance service.
Three special monitor operation modes can be
chosen by means of jumpers 2, 3 and 4 located
on monitor's printed card, figure 6.
NOTE. The ON position is achieved by inserting the
jumper across 2 pins to assure alectric connection.
The jumper must be inserted on 1 pin only when OFF
6
position is required. See detail on top of fig. 6.
• Monitor in constant mode
For use only in single house installations as close
circuit television system with camera always powe-
red and separated from entry panel.
VMF/100 is supplied from the factory with jumper 2
in the OFF position.
The constant mode is achieved with jumper 2 set to
ON position. The monitor can only be switched off
by thumbwheel switch D, figure 1.
• Activation of more monitors by the same call
Jumper 3 is normally kept in the ON position, this
way the call line loop is closed. If more monitors
must be activated by the same call, leave only one
with the jumper 3 in the ON position, all other moni-
tors must have the jumper 3 in the OFF position.
• Monitor/system turned off on door release
a) Systems with VA/100 main control unit
Jumper 4 is normally kept in the OFF position. In
this position the monitor is turned off automatically
by the system timer.
Whit Jumper 4 in the ON position the monitor is tur-
ned off by pressing the door lock release button.
b) Systems with VA/100.01 main control unit
Jumper 4 must be in the OFF position
Use dip-switch 2 of the VA/100.01 main control unit
to turn off the monitor.
Call tone
It is possible to regulate the call tone level from the
entry panel by adjusting the trimmer P1, figure 6.
System using main control unit VA/100.01 has a
timed call feature.
The call stops either when the handset is lifted or
when any
button is pressed.
Function of each terminal, figure 6
1
video signal
(
1
)
2
video signal shield
3
video signal
4
video signal shield
5
– 14÷17.5 V
6
+ supply voltage to monitor
7
call
8
audio to monitor
9
audio to entry panel
10 11.5 V DC voltage output (
2
)
or input to turn on monitor when connected to
positive voltage system (+15÷17.5 V DC)
11 Aux 1
12 Aux 2
13 LED 1 (green)
14 LED 2 (yellow)
15 LED 3 (red)
(
1
) 75 Ω closing resistance if video line stops here
(
2
) This voltage output is available for the time the
monitor is operating. Max. current demand should
not exceed 50 mA.
NOTE. Connect wires to terminals in accordance to
VM/100 diagrams.
Technical features
• Picture screen: 4" (10 cm).
• Supply voltage: 14÷17.5 V DC.
• Max. current demand: 400 mA (5 mA quiescent).
• Current demand per LED: 7 mA.
• Bandwidth response at -3 dB: 6 MHz.
• Video input: 1 Vpp (from 0,7 Vpp to 2 Vpp).
• Video input impedance: >15 KΩ.
• Call signal: electronic dual tone note, the call
volume can be regulated.
• Aux 1 and Aux 2: normally open switch, when
actuated the contact closes to 0 V DC.
• Current demand should not exceed 100 mA at 24 V.
• Working temperature range: from 0 °C to +35 °C.
• Dimensions: 195 x 230 x 72 mm.
INSTALLATION
WARNING. It is recommended to install the
monitor in a dry place.
Slide the locking latch as shown in figure 2A. Slide
the steel frame out, and fix it on the wall at a suita-
ble height by using the screws and retainers inclu-
ded in the pack.
Please, pay attention to place the frame with the
indication TOP in upper position, and make the holl
figure 3, to coincide with the cable junction box.
Publicidad
