Publicidad
Idiomas disponibles
Idiomas disponibles
checking the efficient function, always check that the mains cable is
correctly assembled.
The hood is provided with a special power cable ; if the cable is damaged,
request a new one from Technical Service.
Mounting
Before beginning installation:
•
Check that the product purchased is of a suitable size for the chosen
installation area.
•
Remove the charcoal (*) filter/s if supplied (see also relative
paragraph). This/these is/are to be mounted only if you want lo use
the hood in the filtering version.
•
Check (for transport reasons) that there is no other supplied material
inside the hood (e.g. packets with screws (*), guarantees (*), etc.),
eventually removing them and keeping them.
•
If possible, disconnect and move freestanding or slide-in range from
cabinet opening to provide easier access to rear wall/ceiling.
Otherwise put a thick, protective covering over countertop, cooktop or
range to protect from damage and debris. Select a flat surface for
assembling the unit. Cover that surface with a protective covering and
place all canopy hood parts and hardware in it.
•
In addition check whether near the installation area of the hood (in the
area accessible also with the hood mounted) an electric socket is
available and it is possible to connect a fumes discharge device to the
outside (only suction version).
•
Carry out all the masonry work necessary (e.g. installation of an
electric socket and/or a hole for the passage of the discharge tube).
Expansion wall plugs are provided to secure the hood to most types of
walls/ceilings. However, a qualified technician must verify suitability of the
materials in accordance with the type of wall/ceiling. The wall/ceiling must
be strong enough to take the weight of the hood. Do not tile, grout or
silicone this appliance to the wall. Surface mounting only.
Operation
Use the high suction speed in cases of concentrated kitchen vapours. It is
recommended that the cooker hood suction is switched on for 5 minutes
prior to cooking and to leave in operation during cooking and for another
15 minutes approximately after terminating cooking.
a - Motor High-speed Button
It could switch from Low-speed to High-speed.
b - Motor Low-speed Button
It controls the low speed of motor.
c - Power Button
It turns on or off the power.All the other buttons are
controlled by Power Button except the Lighting Button.
d - Lighting Button
It turns on and off the lamp.
e - Delayed Switch-off Button
Push this button slightly when the motor works, the
indicator light starts blinking, then the motor stops after
three minutes: In this Delayed status, it cancels the
operation while pushing the button once.
Control panel of 4-button switch
a ON/OFF switch for lighting
b 1-speed OFF switch
c 2-sppeed selection
d 3-speed selection
BOIXN switch
0
d
1 – Start/ dynamo grade-1 gear
The dynamo can be started, and the dynamo enters the low gear
2 – Start/ dynamo grade-2 gear
The dynamo can be started, and the dynamo enters the middle gear
3 – Start/ dynamo grade-3 gear
The dynamo can be started, and the dynamo enters the high gear.
a – Turn on the lighting
The lighting can be turned on
b - Start / dynamo grade-1 gear and lighting
The dynamo enters the low gear and then turn on the lighting
c - Start / dynamo grade-2 gear and lighting
The dynamo enters the middle gear and then turn on the lighting
d - Start / dynamo grade-3 gear and lighting
The dynamo enters the high gear and then turn on the lighting.
Maintenance
ATTENTION! Before performing any maintenance operation, isolate the
hood from the electrical supply by switching off at the connector and
removing the connector fuse.
Or if the appliance has been connected through a plug and socket, then
the plug must be removed from the socket.
Cleaning
The cooker hood should be cleaned regularly (at least with the same
frequency with which you carry out maintenance of the fat filters) internally
and externally.
Clean using the cloth dampened with neutral liquid
detergent. Do not use abrasive products. DO NOT USE ALCOHOL!
WARNING: Failure to carry out the basic cleaning recommendations of
the cooker hood and replacement of the filters may cause fire risks.
Therefore, we recommend observing these instructions.
The manufacturer declines all responsibility for any damage to the motor
or any fire damage linked to inappropriate maintenance or failure to
observe the above safety recommendations.
Grease filter
Traps cooking grease particles.
This must be cleaned once a month (or when the filter saturation
indication system – if envisaged on the model in possession – indicates
this necessity) using non aggressive detergents, either by hand or in the
dishwasher, which must be set to a low temperature and a short cycle.
When washed in a dishwasher, the grease filter may discolour slightly, but
this does not affect its filtering capacity.
To remove the grease filter, pull the spring release handle.
Replacing lamps
Fig. 10
Disconnect the hood from the electricity.
Warning! Prior to touching the light bulbs ensure they are cooled down.
Replace the old light bulb with the one of the same type as specified in the
feature label or near the light lamp on the hood.
1. Using a small flat head screwdriver or equivalent tool, carefully pry
outwards and pull out connector plug.
2. Remove the damaged light and replace with a new 12 Volt, 1.5 Watt
(Maximum) LED light or a new 12 Volt, 20 Watt (Maximum) halogen
lamp made with same specification.
Follow package directions and do not touch new light with bare hands.
3. Reinstall the light cover. (it will snap shut).
If the lights do not work, make sure that the lamps are fitted properly into
their housings before you call for technical assistance.
For replacement, contact the technical service.
Publicidad
