Description Of Symbols; General Safety; Electrical Safety - Silverline 124986 Manual Del Usuario

GB

Description of Symbols

The rating plate on your tool may show symbols. These represent important
information about the product or instructions on its use
Wear hearing protection
Wear eye protection
Wear breathing protection
Wear head protection
Wear hand protection
Read instruction manual
Double insulated for additional protection
Conforms to relevant legislation and safety standards
Environmental Protection
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist. Check
with your local authority or retailer for recycling advice
Specification
Voltage .................................................230V~
Frequency ............................................50Hz
Power ...................................................1020W
No load speed ......................................16,000min
Max depth of cut ..................................3.0mm
Blade size.............................................82mm
Weighted vibration ...............................2.631m/s
Uncertainty ...........................................1.5m/s
Sound pressure ....................................94.9dB(A)
Sound power ........................................107.9dB(A)
Uncertainty ...........................................3dB(A)
Protection class ....................................
The sound intensity level for the operator may exceed 85dB(A) and
sound protection measures are necessary.
As part of our ongoing product development, specifications of
Silverline products may alter without notice.
4
All manuals and user guides at all-guides.com
-1
2
2
Carefully read and understand this manual and any label attached to the tool before use.
Keep these instructions with the product for future reference. Ensure all persons who use
this product are fully acquainted with this manual.
Even when used as prescribed it is not possible to eliminate all residual risk factors. Use
with caution. If you are at all unsure of the correct and safe manner in which to use this
tool, do not attempt to use it.

General Safety

Clean the work area
• Accidents can occur where benches and work areas are cluttered or dirty. Keep floors
clear and avoid working where the floor is slippery. If working outdoors, be aware of all
potential slip and trip hazards before using this tool
Children and pets
• Keep children and pets at a safe distance from the work area. Lock tools away where
children cannot gain access
Trained, competent persons
• This tool should be used by trained, competent persons only
Wear suitable clothing and footwear
• Do not wear loose fitting clothing, neckties, jewellery, or other items which may become
caught. Wear non-slip footwear or, where appropriate, footwear with protective toe caps.
Long hair should be covered or tied back
Protective equipment
• Refer to the rating plate on your tool for information relating to the necessary protective
equipment when using this product. Example; dust mask/respirator, goggles, ear
defenders, gloves etc
Check for damaged or missing parts
• Before each use, check if any part of the tool is damaged or missing. Carefully check
that it will operate properly and perform its intended function. Check alignment
of moving parts for binding. Any guard or other part that is damaged should be
immediately repaired or replaced by an authorised service centre. DO NOT USE IF
DEFECTIVE
Use the correct tool
• Do not force or attempt to use a tool for a purpose for which it was not designed. This
tool is not intended for industrial use
Accessories
• The use of any attachment or accessory, other than those mentioned in this manual,
could be dangerous and result in damage or injury, and may invalidate your warranty
Keep guards in position
• Where guards exist keep them in position, in good working order, correctly adjusted and
aligned. Never attempt to use a tool if any of the supplied guards are missing. If any
guards are damaged, replace before use
Remove adjusting keys
• Where adjusting keys exist, ensure they are removed prior to using the tool. Always
check to see that keys and adjusting devices are removed from the tool before use
Secure work
• Where possible, always secure work. If appropriate, use a clamp or vice so that both
hands are free to operate the tool
Keep your balance
• Do not over-reach. Keep secure footing at all times and do not use tools when standing
on an unstable surface
Never stand on your tool
• Standing on your tool or its stand could cause serious injury if the tool is tipped or
collapses. Do not store materials above or close to the tool in such a way that a person
might stand on the tool to reach the stored items

Electrical Safety

Dangerous environment
• Do not use power tools in damp or wet conditions, or expose them to rain. Provide
adequate surrounding work space and keep the area well lit. Do not use power tools
where there is a risk of explosion or fire from combustible material, flammable liquids,
flammable gases, or dust of an explosive nature. When using power tools, avoid contact
with any earthed items such as pipes, radiators, cookers, refrigerators, metal baths
and taps
Protect yourself from vibration
• Hand-held power tools may produce vibration. Vibration can cause disease. Gloves may
help to maintain good blood circulation in the fingers. Hand-held tools should not be