Tabla de contenido
Publicidad
Limpieza y mantenimiento especial
Conjunto del filtro
Para obtener el mejor rendimiento y los mejores resultados es
necesario limpiar el filtro.
El filtro elimina las partículas de comida del agua utilizada en el
lavado y permite que recircule durante el programa. Por esta
razón, se aconseja quitar las partículas de comida más grandes
depositadas en el filtro, después de cada lavado. Para ello, limpie
el filtro semicircular y el tapón (A) con agua corriente. Para extraer
el conjunto del filtro, tire del asa del tapón hacia arriba. Todo el
conjunto del filtro (compuesto por un filtro semicircular (A) y un
filtro fino (B)) deben limpiarse al menos una vez al mes. Para
limpiar el filtro y el filtro de malla fina, utilice un cepillo. A
continuación, vuelva a montar las piezas del filtro como se
muestra en la figura, coloque todo el conjunto en su
emplazamiento en el lavavajillas y presiónelo hacia abajo.
No utilice nunca el lavavajillas sin los filtros. Si se insertan los
filtros de forma incorrecta se reduce el rendimiento del aparato y
puede dañarse la vajilla y los utensilios.
Instalación
1. Se cae la máquina, la fachada principal de ella hacia arriba.
2. Desenrosca el tornillo que está debajo de la barra de adorno
con el destornillador (dibujo A), y también con él levanta la
pata empujándola desde dentro de la barra de adorno del
soporte (no use la fuerza muy fuerte, previene que se rompe
la pata), deshace la barra de adorno donde está debajo de la
puerta (debujo B).
3. Afloja el tornillo fijo de la barra de adorno de cáscara de
puerta (dibujoC--D).
4. Incrusta la tabla para adorno en la puerta y la barra de adorno
de cáscara de la puerta, desarrúguela, aprétela, luego, apreta
los tornillos los que están en ambos lados de tabla de adorno
y debajo.
5. Instala la barra de adorno para restituirla.
6. Alza la máquina.
Atención:
1. Espeso de tabla de adorno no puede exceder 2 mm.
2. Medidas para el exterior la tabla de adorno son 585 0.5
mmX597 0.5mm.
All manuals and user guides at all-guides.com
Limpieza de los brazos aspersores
Puede ocurrir que las partículas de alimentos se incrusten en los
brazos aspersores y bloqueen los orificios (vea el apartado
"Primer plano" [Interior], letras C-E). Compruebe los brazos
aspersores de forma periódica y límpielos siempre que sea
necesario.
A
B
A
C
D
.49.
Turning on the Appliance
Starting a wash cycle
- Make sure that the plug of the appliance is inserted into the wall
socket.
- Make sure that the water supply is turned on to full pressure.
- Load the dishwasher (see the section "Loading the
Dishwasher").
- Pour in the detergent (see the section "Salt, Detergent and Rinse
Aid").
- Turn the knob located on the right of the control panel clock
wise to the desired cycle number or symbol (see the section
"Wash Cycle Table").
- Press the ON-OFF button; the ON-OFF light will turn on. At this
point, the wash cycle will begin.
If you forget to load some of dishes
The wash cycle can be interrupted by pressing the ON-OFF
button. You can then load additional dishes and turn the appli-
ance back on. The appliance will resume operation from where it
was interrupted.
At the end of the wash cycle
When the knob stops turning and is aligned with the STOP mark
(see figure), the cycle has finished. Turn off the appliance using
Troubleshooting
It may occur that the dishwasher does not function or does not
function properly. Before calling for assistance, see what can be
B
done first: have you forgotten to press one of the buttons or to
perform an essential operation?
The Dishwasher Does Not Start
Have you checked whether:
- the plug is pushed into the socket correctly;
- the power is on in the house;
- the door is closed properly;
- the ON-OFF switch is on "ON";
- the water supply is turned on.
The Dishwasher Does Not Load Water
Have you checked whether:
- the water is turned on and the hose is connected properly;
- the water supply to the house is on and has sufficient pressure;
- the water supply hose is crimped or bent;
- the filter for the water supply hose is clogged.
The Dishes Are Not Clean
Have you checked whether:
E
- the water is turned on and the hose is connected properly;
ES
GB
the ON-OFF button, turn off the water supply and open the door
of the dishwasher.
Wait a few minutes before unloading the dishwasher to avoid
handling the dishes and utensils while they are still hot and more
susceptible to breakage. They will also dry better.
Cancelling or modifying a wash cycle setting
Premise: A cycle that is underway can only be modified if it
has been running for a short time. Otherwise, the detergent
may have already been used, and the appliance may have
already drained the wash water. If this is the case, the deter-
gent dispenser must be refilled (see paragraph "Loading the
detergent").
Press the ON-OFF button and the ON Light will turn off. Rotate
the knob clockwise to the desired cycle setting (see the section
"Starting a wash cycle"). Then, turn the dishwasher back on us-
ing the ON-OFF button.
- the water supply to the house is on and has sufficient pressure;
- the water supply hose is crimped or bent;
- the filter for the water supply hose is clogged.
The Dishwasher Does Not Drain
Have you checked whether:
- the drain hose is crimped or bent.
Lime Deposits or a White Film Form on the Dishes
Have you checked whether:
- the lid of the salt container is closed properly;
- the rinse aid dosage is correct.
If, despite all these checks, the dishwasher still does not function
and/or the problem persists, contact the nearest authorised ser-
vice centre and provide the following information:
- the nature of the problem;
- the model type number (Mod...) and the serial number (S/N...),
which are indicated on the plate located on the side of the inner
part of the door.
Never call unauthorised technicians and refuse to allow parts
to be installed that are not original spare parts.
.6.
Publicidad
Tabla de contenido
