STERWINS 20VGS2-13.1 Manual Del Usuario página 168

• AMBIENT TEMPERATURE RANGE FOR TOOL DURING OPERATION IS
FR
BETWEEN 0°C AND 40°C.
• ROOM TEMPERATURE RANGE FOR TOOL STORAGE IS BETWEEN 4°C AND
ES
24°C.
• THE RECOMMENDED ROOM TEMPERATURE RANGE FOR THE CHARGING
SYSTEM DURING CHARGING IS BETWEEN 10°C AND 38°C.
PT
• IF YOU SHALL REPLACE THE CUTTING BLADE, MAKE SURE THAT THE
FOLLOWING CHARACTERISTICS ARE THE SAME : SAME SHAPE, SAME LENGTH,
IT
SAME THICKNESS, SAME WEIGHT, SAME MATERIAL.
• KEEP HANDS AWAY FROM BLADE
• BEWARE OF THROWN OBJECT
EL
• DO NOT USE CRACKED OR DISTORTED GARDEN SAWS. DO NOT USE GARDEN
SAWS THAT ARE DAMAGED OR DEFORMED.
PL
• OPERATION SAFETY WARNING
• CHECK THE PRODUCT, ITS BATTERY PACK AND CHARGER AS WELL AS
ACCESSORIES FOR DAMAGE BEFORE EACH USE. DO NOT USE THE PRODUCT IF
RU
IT IS DAMAGED OR SHOWS WEAR.
• DOUBLE CHECK THAT THE ACCESSORIES AND ATTACHMENTS ARE PROPERLY
KZ
FIXED.
• ALWAYS HOLD THE PRODUCT ON ITS HANDLE. KEEP THE HANDLE DRY TO
ENSURE SAFE SUPPORT.
UA
• ENSURE THAT THE AIR VENTS ARE ALWAYS UNOBSTRUCTED AND CLEAR.
CLEAN THEM IF NECESSARY WITH A SOFT BRUSH. BLOCKED AIR VENTS MAY
LEAD TO OVERHEATING AND DAMAGE THE PRODUCT.
RO
• SWITCH THE PRODUCT OFF IMMEDIATELY IF YOU ARE DISTURBED WHILE
WORKING BY OTHER PEOPLE ENTERING THE WORKING AREA. ALWAYS LET
EN
THE PRODUCT COME TO COMPLETE STOP BEFORE PUTTING IT DOWN.
• DO NOT OVERWORK YOURSELF. TAKE REGULAR BREAKS TO ENSURE YOU
CAN CONCENTRATE ON THE WORK AND HAVE FULL CONTROL OVER THE
PRODUCT.
• BEFORE SWITCHING THE PRODUCT ON, CHECK WHETHER IT HAS BEEN
ASSEMBLED CORRECTLY AND ALL THE MOVING PARTS ARE RUNNING
SMOOTHLY.
• WE RECOMMEND SLIGHTLY DAMPENING SURFACES IN DUSTY CONDITIONS
OR USING A MISTER ATTACHMENT.
• ONLY OPERATE THE PRODUCT AT REASONABLE HOURS – NOT EARLY
IN THE MORNING, LATE AT NIGHT OR ON WEEKENDS/PUBLIC HOLIDAYS
WHEN PEOPLE MIGHT BE DISTURBED. INFORM YOURSELF ABOUT LOCAL
RESTRICTIONS
• AVOID USING THE PRODUCT IN BAD WEATHER CONDITIONS, ESPECIALLY
WHEN THERE IS A RISK OF LIGHTNING. DO NOT OPERATE THE PRODUCT IN
POOR LIGHTING. THE OPERATOR REQUIRES A CLEAR VIEW OF THE WORK AREA
TO IDENTIFY POTENTIAL HAZARDS.
• USE OF HEARING PROTECTION REDUCES THE ABILITY TO HEAR WARNINGS
(SHOUTS OR ALARMS). THE OPERATOR MUST PAY EXTRA ATTENTION TO WHAT
IS GOING ON IN THE WORK AREA. DO NOT GET DISTRACTED, AND ALWAYS
CONCENTRATE ON THE TASK.
• OPERATING SIMILAR TOOLS NEARBY INCREASES BOTH THE RISK OF
HEARING INJURY AND THE POTENTIAL FOR OTHER PERSONS TO ENTER YOUR
WORK AREA.
• KEEP FIRM FOOTING AND BALANCE.
• DO NOT OVERREACH. OVERREACHING CAN RESULT IN LOSS OF BALANCE.
ALWAYS BE SURE OF THE FOOTING ON SLOPES.
• WALK, NEVER RUN. KEEP ALL PARTS OF YOUR BODY AWAY FROM ANY
MOVING PART.
• NEVER RUN THE PRODUCT WITHOUT THE PROPER EQUIPMENT ATTACHED.
• DO NOT MODIFY THE PRODUCT IN ANY WAY OR USE PARTS AND
ACCESSORIES THAT ARE NOT RECOMMENDED BY THE MANUFACTURER.
• IF THE PRODUCT IS DROPPED, SUFFERS HEAVY IMPACT OR BEGINS TO
VIBRATE ABNORMALLY, IMMEDIATELY STOP THE PRODUCT AND INSPECT FOR
DAMAGE OR IDENTIFY THE CAUSE OF THE VIBRATION. ANY DAMAGE SHOULD
BE PROPERLY REPAIRED OR REPLACE BY AN AUTHORIZED SERVICE CENTRE.
• TO REDUCE THE RISK OF INJURY ASSOCIATED WITH CONTACTING ROTATING
PARTS, ALWAYS STOP THE MACHINE, REMOVE THE BATTERY PACK, AND MAKE
SURE ALL MOVING PARTS HAVE STOPPED:
- BEFORE CLEANING OR CLEARING A BLOCKAGE
- WHEN LEAVING THE PRODUCT UNATTENDED
- BEFORE INSTALLING OR REMOVING ATTACHMENTS
- BEFORE CHECKING, MAINTAINING OR WORKING ON THE PRODUCT
168