Intercom Function; Default Settings - Bitronvideo B-FAST AV1407/005 Manual De Instrucciones

ON
DER USER
1 2 3 4 5
ON ON
ON
1 2 1 2 3 4 5 1 2 3 4 5
ON
1 2 3 4 5
ON
1 2 3 4 5
ON
1 2 3 4 5
ON
1 2 3 4 5
ON
1 2 3 4 5
ON
1 2 3 4 5
DER: Apartment internal code
This code is used to identify the single internal devices of the same user. This allows to make intercom calls
adressed to the single internal code in the same apartment. Set a number from 0 to 31 according to the
following fi gure and rules:
• If in the apartment there is only one door phone, the internal code must be set to 0;
• In apartments can be connected up to 4 door phones or monitors in parallel with the same user code and
different internal codes;
• If in the apartment there are several door phones and/or video door phones, it is better that the internal
code no. 0 is a video door phone device, in order to receive images during the call.
• The internal codes confi gured with code DER 0 and 1will ring immediately when the call is received; the
internal codes 2 and 3 will ring immediately after.
DER USER
ON ON
ON
1 2 1 2 3 4 5
1 2

DEFAULT SETTINGS

Default settings of B-fast AV1407/005 door phones are the following:
1 2
Impedance
selector
12
All manuals and user guides at all-guides.com
ON ON ON
User User User
0 1 2
1 2 3 4 5 1 2 3 4 5 1 2
ON ON ON
User User User
4 5 6
1 2 3 4 5 1 2 3 4 5 1 2
ON ON ON
User User User
8 9 10
1 2 3 4 5 1 2 3 4 5 1 2
ON ON ON
User User User
12 13 14
1 2 3 4 5 1 2 3 4 5 1 2
ON ON ON
User User User
16 17 18
1 2 3 4 5 1 2 3 4 5 1 2
ON ON ON
User User User
20 21 22
1 2 3 4 5 1 2 3 4 5 1 2
ON ON ON
User User User
24 25 26
1 2 3 4 5 1 2 3 4 5 1 2
ON ON ON
User User User
28 29 30
1 2 3 4 5 1 2 3 4 5 1 2
DER
ON ON ON
Indoor Indoor Indoor Indoor
station station station station
0 1 2 1 1 2 2 1 2 3
USER DER
ON ON
3 4 5 1 2
USER = 31
OFF
DER = 0
SI = ON
ON

INTERCOM FUNCTION

User
3
In B-Fast door phone it is possible to programm only the button "o" for intercom call function.
3 4 5
The button can be programmed to call another user in the system or to call a door phone or a monitor of the
User
same user programmed as another internal code (DER). In the fi rst case all door phones or monitors of the
7
called user will ring; in the second case only the door phone or monitor of the specifi ed internal code will
3 4 5
ring.
User
If intercom calls must be performed with several users, it is possible to add the button additional module
11
3 4 5
appropriate for B-fast AV1407/051 application.
User
INTERCOM FUNCTION BETWEEN SEVERAL USERS
15
3 4 5
1. Go to the door phone to be programmed as caller (door
User
phone'a').
19
3 4 5
2. Hold the door opener button pressed and pick up the
handset. The door phone'a' emits two beeps to signal
User
23
the access to programming mode.
3 4 5
User
27
3 4 5
User
31
3 4 5
3. Press the button"•" to be programmed; the door phone
emits a confi rmation tone.
4. Go to the user to be called by the button"•": User 'b'.
Press the door opener button.
The calling door phone and the called door phone or
video door phone will emit a beep to indicate they
have been programmed. Alternatively, go to a calling
station and press the calling button of user 'b'; the
calling door phone 'a' in programming mode will beep
to signal that it has been programmed. At the same
time, the door phones or monitors of user 'b' will ring.
Ignore this call.
5. Hang up the handset of calling door phone'a', that will
beep to indicate the exit from programming mode.
6. Check immediately the programmed function: hang up
the handset of door phone 'a' and press the programmed button. Check that all door phones or monitors
of user 'b' ring; hang up the handset of a door phone or monitor 'b' and check that it is possible to
communicate with monitor 'a'.
7. If you want to make the inverse call from'b' to 'a', it is necessary to programm also the door phone or
monitor 'b' to call the door phone 'a' as described in the previous sections.
If the button"•" is programmed for intercom function, the auto-on functions will not be lost (video cyclic
and video transfer*), because these are performed when the handset is on hook.
DS90330-003A DS90330-003A
'a'
'a'
'b'
13