POWER SMITH PWLD140T Manual Del Operario página 4

ASSEMBLY INSTRUCTIONS
attacHInG WoRk LIGHt HeaDs to
stanD (FIG 2)
1.
Place the stand (7) on a flat surface.
2.
Rotate the carrying handle (1) straight up. Tighten the
handle locking knob (G3) to secure it in place.
3.
Install one work light head (2) on the stand (7) by sliding
and positioning the U-shape bracket (10) under the bolt
cap (G2) as shown in FIG 2. Tighten the locking knob
(G1) to secure the work light head in place. Repeat the
procedure on the second work light head.
4.
Hang the power cable splitter (H) on the hook (G4).
settInG Up anD aDJUstInG tHe
tRIpoD (FIG 2)
1.
Loosen the tripod locking knob (F).
2.
Push down the leg connector (A) until the legs (B) are
fully extended and firmly tighten the locking knob (F).
3.
Adjust the height of the tripod by unlocking the flip
locks (C1 & C2) and raising the center poles (D1 & D2)
of tripod. Lock the flip locks when the tripod reaches
desired height.
NOTe:
The maximum height of this tripod is 60".
attacHInG tHe WoRk LIGHt
asseMBLY to tHe tRIpoD (FIG 3)
1.
Place the work light assembly on top of the tripod.
2.
Use the bracket locking system (E1, E2 and E3) to secure
the work light assembly to the tripod as shown in FIG 3.
NOTe:
Make sure the two locking brackets (E1) are over the
raised metal plate in the middle of the stand.
caUtIon:
•
Keep the metal parts of light away from any live power
source.
•
Prior to installation and maintenance of the light,
disconnect the light from power source to prevent
electric shock.
•
Installing and operating the light in harsh environments
may shorten the lifespan and/or damage the light.
•
Keep the light away from any corrosive substance and
only clean with dry cloth and non-abrasive cleaner.
•
To ensure personal safety, make sure the light is
mounted firmly and securely when installed in a high
position.
OPERATION
aDJUstInG tHe LIGHt DIRectIon
Your work light can be tilted vertically from 30° down to
90° up.
English
to adjust the light Direction, loosen the side locking
knobs (4-FIG 1). Adjust the work light head to desired
position, and retighten knobs.
sWItcH actIon
Each of the work light heads is equipped with an On/Off
switch (5-FIG 1) located on the back side of the work light.
Press the switch once to turn the work light on and press
the switch a second time to turn it off. Always turn the work
light off before unplugging.
WaRnInG:
is unplugged and completely cool before attempting to
clean it.
Your work light requires very little care and maintenance.
Simply clean the lens regularly with a non-abrasive cleaner.
This product is warranted free from defects in material and
workmanship for 5 (Five) years after date of purchase. This
limited warranty does not cover normal wear and tear or
damage from neglect or accident. The original purchaser is
covered by this warranty and it is not transferable. Prior to
returning your product to store location of purchase, please
call the Toll-Free Help Line for possible solutions.
For questions about this or any other PowerSmith
product,
Please call Toll-Free:
Or visit our website:
www.
powersmithproducts.com
4
OPERATION
MAINTENANCE
Always make sure the work light
WARRANTY
HELP LINE
888-552-8665.
®