Publicidad
Idiomas disponibles
Idiomas disponibles
FUNZIONAMENTO - WORKING - FONCTIONNEMENT - FUNKTIONSTÄTIGKEIT -
START/SWITCH OFF
It is switched on pressing any light check pushbutton: it starts with an automatic chromotherapy cycle.
To switch off push the key "ON/OFF" (with the system on).
WARNING: after 60 minutes from start the device switches off automatically.
AUTOMATIC CHROMOTHERAPY CYCLE
Automatic chromotherapy cycle start pushing any time the key "COLOUR"; cycle start is signaled by a blink of white LEDs.
Color sequence is WHITE, RED, ORANGE, YELLOW, GREEN, LIGHT BLUE, BLUE, VIOLET.
The complete cycle lasts around 2 minutes (around 13 seconds per colour).
MANUAL COLOR SELECTION
Any time, pushing the bar "COLOUR SWEEP", the LEDs will execute the reference colour pushed; any automatic program running will
be stopped.
INTENSITY REGULATION
With enabled system, pressing the keys "LIGHT DIMMER", the LED intensity will be reduced or increased according to the pressed key,
without interfering with any automatic cycle.
The remote control for the audio module check allows managing the following functions:
PLAY/PAUSE (BLUETOOTH PAIRING)
• External audio device (not supplied) to be paired – Bluetooth pairing will be visible for a short period pressing the audio module
pushbutton.
• External audio device (not supplied) already paired – Pressing the pushbutton manages the PLAY/PAUSE function of the external
audio device.
NEXT TRACK – PREV TRACK
Pressing one of the two pushbuttons switches to the next or previous song, if provided on the external audio device.
VOLUME CONTROL
Pressing one of the two pushbuttons, sound intensity is increased or reduced.
Time-out modes provided are the following:
•
After 1 hour (standard configuration)
•
After 12 Hours
•
NO time-out
To start the configuration mode it is necessary:
1.
to cut power supply to control unit
2.
restore the power supply to the control unit; it is signaled by LED flashing RED-GREEN-BLUE-WHITE
3.
from this moment the control unit enters the "coupling stand by" phase for about 30 seconds
4.
push key ON/OFF and one of the following keys for audio control at the same time:
•
ON/OFF + VOLUME DOWN down (1 hour) - the flashing of BLUE LED confirms it
•
ON/OFF + PREV TRACK in the middle (12 hours) - the double flashing of BLUE LED confirms it
•
ON/OFF + NEXT TRACK up (NO time-out) - the triple flashing of BLUE LED confirms it
5.
wait, without pressing anything, the end of the coupling phase indicated by the LED with a WHITE flash
WARNING: the configuration can be obtained ONLY if the remote controls has been already coupled.
This function allows the deactivation of the led colours: only the WHITE colour remains active.
To start the configuration mode it is necessary:
1.
to cut power supply to control unit
2.
restore the power supply to the control unit; it is signaled by LED flashing RED-GREEN-BLUE-WHITE
3.
from this moment the control unit enters the "coupling stand by" phase for about 30 seconds
4.
to push at the same time the key COLOUR and the COLOUR SWEEP in this way:
•
COLOUR + COLOUR SWEEP on RED - STANDARD COLOURS operation is active - the flashing of the RED-GREEN-BLUE-
WHITE LED confirms it
•
COLOUR + COLOUR SWEEP on WHITE - "ONLY WHITE" operation is active - the flashing of the WHITE LED confirms it
5.
wait, without pressing anything, the end of the coupling phase indicated by the LED with a WHITE flash
WARNING: the configuration can be obtained ONLY if the remote controls has been already coupled.
This function allows limiting Bluetooth pairing to a singular device at a time and cancels the pairing after 72 hours of inactivity.
In order to start the configuration mode it is necessary:
1.
to interrupt the power supply to the control unit
2.
to reset the power supply to the control unit
3.
from this moment on the control unit enters the "pairing phase" for about 30 seconds
4.
press at the same time keys COLOUR and PLAY/PAUSE
•
FUNCTION ENABLED: indicated by 3 RED flashes on the remote control
•
FUNCTION DISABLED: indicated by 1 RED flash on the remote control
5.
waiting for the end of the pairing phase without pressing anything.
FUNCIONAMIENTO - ИСПОЛЬЗОВАНИЕ - ΛΕΙΤΟΥΡΓΙΑ - 运行
LIGHT CHECK CONTROL (if chromotherapy module is installed)
AUDIO CHECK CONTROLS (IF THE AUDIO MODULE IS INSTALLED)
TIME-OUT CONFIGURATION (for chromotherapy module only)
"ONLY WHITE" OPERATION (for chromotherapy module only)
"HOTEL MODE BLUETOOTH" OPERATION
14
Publicidad
