ItsImagical Droni Stream Manual Del Usuario página 10

9. MODE 2
Operating direction
Hover up and down
Push the throttle up or down, the quadcopter flies upward or downward.
Forward and backward
Push the direction lever up or down, the quadcopter flies forward or backward.
Turn Left and Right
Pull the direction lever left or right, the quadcopter turns to left or right.
Sideward fly
Pull the throttle left or right, the quadcopter flies to left side or right
Fine-tuning operation
Forward/Backward fine-tuning
When the quadcopter keeps flying forward / backward, you can correct
it by pressing fine-tuning button down / up.
Sideward fly fine-tuning
When the quadcopter keeps flying to left / right side, you can correct it by
pressing the Fine-tuning button right / left.
Turn left/right fine-tuning
When the quadcopter keeps rotating to left / right, you can correct it by
pressing the finetuning button right / left.
10. Ready to fly your quadcopter
1. Press the ON/OFF power switch up.
2. Open battery cover, and connect battery connector with dash receiver.
3. Enclose battery into the fuselage, after closing battery cover, turn on the
switch on
the bottom of aircraft.
4. Push the throttle lever to the highest position, and then pull it back to the
lowest position. There will be one clear sound from the transmitter, this shows
that the quadcopter has entered into the pre-fly state.
11. Function introduction
1. Low-voltage protection:
When four indicator lights on the bottom of aircraft start to flicker, it means
electric quantity of the aircraft is insufficient. Please control the aircraft to make
a return voyage.
2. Over-current protection:
In the condition of rotating aircraft's fan blade, when being crashed or stuck,
aircraft's circuit will conduct over-current protection.
3. Horizontal correcting function:
Place the quadcopter on a horizontal postion, then push transmitter both left
and right lever to lowest right conner for about 2-3 second, indicator on the
quadcopter changed from normal lights up to quickly flashing ;After 2-3 second
,the indicator changed to normal lights, it means the quadcopter restarted
/reset successfully.
4. 3D eversion:
Tips:3D eversion goes better when battery power is enough.
When you are familiar with the basic operation, you can do some awesome&
exciting tricks and stunts! First of all,fly the aircraft to a height of more than 3
meters, press the 3D Eversion switch on the rear right side of the transmitter,
then push the right rudder(in any direction) to make 360 degree flip.
5. Throwing flight instructions:
Thanks to the 6 axis gyroscope,you can throw the quadcopter and push the
throttle right up,it will automatically level out and hover smoothly in the sky,
This can also be done when the quadcopter is rolling.
6. Headless function:
Forward definition
6.1. Turn on power switch of remote control.
6.2. After aircraft connects with power supply, place the switch in "ON" position,
adjust the direction pointed by aircraft's handpiece and regard it as the dead
14. Maintenance procedure
Problems
1. Aircraft enters into low-voltage protection.
2. Electric quantity of remote control is insufficient, power indicator light will
Aircraft has no response flicker.
3. Channel selection of remote control is inconsistent with aircraft's match
codes.
1. Insufficient remote control's electric quantity.
Aircraft's flying response is insensitive
2. Remote control with the same frequency is transmitting interference.
When hovering, side flight is formed
1. Have no horizontal correction.
In headless state, it deviates to dead ahead 1. Head deflection is caused by multiple collisions.
Length of fuselage: 315mm.
Height of fuselage: 105mm.
Width of fuselage: 315mm.
Battery: 3.7 V. 500 mAh.
Code of main engine: diameter 8.
All manuals and user guides at all-guides.com
ahead in headless situation.
6.3. Push the accelerator's push rod of remote control to the highest point and
pull back to the lowest point.
When remote control pops, it indicates that frequency modulation and forward
definition have already finished.
Switch to headless function and general function
6.4. After frequency modulation, the aircraft defaults to general pattern. The
indicator light on aircraft is long bright state. After pressing down headless
function switch on the top left of master remote controller for 2 seconds, remote
control will give out "DDD...", it means that it enters into headless state. After
pressing for 2 seconds and hearing long "D", it means that it exits headless
state.(In headless mode, four indicators on the aircraft flicker slowly for once
within four seconds)
6.5. In headless state, the operator has no need to recognize the position of
aircraft's headpiece, and he just needs to control the aircraft in accordance with
the direction of remote control's operating rod.
Correcting forward direction
6.6. After aircraft crashes in headless state, if there is deviation in head
direction, it just needs to adjust the aircraft's direction again, pull remote
control's accelerator and operating rod to bottom left simultaneously. When
indicator light on the aircraft flickers for slow three seconds, it means that
correction is done.
12. Change battery of quadcopter
1. Push the on/off switch of quadcopter to OFF position then open the battery
cover.
2. Pull out the battery wire from the power port.
3. To charge battery, please insert the USB port of provided USB charging
cable to anyone USB port of computer.
The indicator on USB cable will light ON during charging battery, than it will
light OFF when battery fully charged.
Caution:
When using the computer for charging,please remember to pull out the
charging cable before shutting down the computer. Take the battery cover, and
close the battery cover on the quadcopter.
4. Reconnect the battery wire to power port than close the battery cover.
Charging time: about 130 minutes — Flying time: about 5.5 minutes!
Cautions when charging:
1. When charging, please put this product on a dried or ventilated area and
keep it far away from heat source or explosive product.
2. When charging, please remove the batteries from the quadcopter. Then
charging process should be supervised by an adult so as not to cause an
accident.
3. When finish flying, please do not charge the battery if the surface
temperature is still not cool. Otherwise it may cause a swollen battery or even
a fire hazard.
4. Please make sure that you use the original USB charging cable provided.
When the battery has been used for a long time, or appears to be swollen,
please replace them.
5. A battery when not in use for a long time will lose its charge automatically.
Charging or discharging too often may reduce the life of the battery.
13. WIFI install camera
Disassembly steps of camera:
1. Pull out power supply cable of the camera as shown in Figure 1.
2. Press safe lock of lower main body forcibly and pull back the camera
simultaneously.
Installation steps of camera:
3. Push the camera in place as shown in Figure 3.
4. Connect connecting line of camera with power supply socket of fuselage´s
camera as shown in Figure 4.
Causes
9
Solutions
1. Charge the aircraft.
2. Change remote control's battery.
3. Adjust channels of remote control and aircraft, and make them become consistent.
1. Battery replacement.
2. Change the place where has no transmitting interference of the same frequency.
1. Conduct horizontal correction, as shown in p.4(correcting function)
1. Define forward again, as shown in p.4(headless function)
(IT
Ca
- L
du
- G
- S
- C
- C
No
1.
po
2.
pe
len
ae
3.
4.
ele
5.
da
co
6.
un
vis
dis
7.
att
di
8.
ve
9.
Ma
1.
2.
3.
po
4.
sm
1.
1)
2)
3)
4)
5)
6)
7)
8)
9)
10
11
2 T
1)
2)
3)
4)
5)
6)
7)
sin
8)
9)
10
1)
2)
co
3.
01
reg
02
03
(re
04
05
06
07
08
so
09
so
10
da
sig
11
12
ma
tra
pa