Power On/Off - ItsImagical Droni Stream Manual Del Usuario

(EN) 4CH 2.4G REMOTE CONTROL QUADCOPTER
Main characteristics
- Four-axis structure is applied, which makes the quadcopter more flexible and
rapid when flying. It has the characteristics of wind-resistant and can be flied
indoor or outdoor.
- Built-in 6 axis gyroscope for precise hovering in the sky.
- Modular design structure is applied, more simple for assembly and convenient
for maintenance.
- With 360°3D eversion function and throwing flight function.
- Added headless function; WI-FI real-time aerial photo.
The materials and specification mentioned in this instruction manual or the
parts inside this package is for reference only. Our company won't be
responsible for any adaption of the outer package. Nor shall we keep our
customers informed in advance. Any information updates or changes, please
be subject to our website.
Safety regulations
1. Please put smaller parts of the aircraft in the place where children can't
reach, avoiding from accidents.
2. Power of this aircraft is adequate. Therefore, when flying for the first time, it
should push remote control's right/left variable-speed joystick slowly, avoiding
from collisions caused by rising aircraft rapidly.
3. After flying, it should turn off remote control's power supply and come close
to the aircraft to turn off its power supply.
4. Please don't put battery in high-temperature and heated places(such as fire
or nearby electric heating devices).
5. When the aircraft flies, it should maintain 2-3 meters from the user or others,
avoiding from crashing into others' head, face or body when it lands.
6. When children operate the aircraft, they should be accompanied with the
adult and guided by the adult. Ensure that the aircraft is controlled within the
range of operator's (or instructor's) visibility. It is convenient for controlling.
7. Non-rechargeable battery can't charge. As installing or changing battery,
please pay attention to the polarity. Don't use a mixture of old and new battery
or battery with different types.
8. When it isn't used, it should turn off remote power supply of remote control
and aircraft, respectively, and take out the battery in remote control.
9. Power supply terminal can't be short circuit.
Maintenance
1. Use clean soft cloth to clean this product frequently.
2. Avoid from exposure or heating in the sun.
3. Don't put the toy in the water. Otherwise, it'll damage electronic parts.
4. Please check the plug and other accessories at regular intervals. If there is
any damage, please stop using it immediately until it is repaired completely.
1. Contents
Product includes following contents:
- Quadcopter
- 2.4G Remote controller
- USB charging wire
- Instruction manual
- Protecting frames
- Phone attaching clamp
- Screwdriver
- Landing gear
- WIFI camera
- Screw
- Blade
2. Get to know your transmitter
Introduction of transmitter:
1. Speed gear's headless function switch
2. Antenna
3. Indicator
4. 3D Eversion
5. Right control lever
6. Forward and backward trimmer
7. Mode switch: Sideward Fine-tuning (Mode 1) / Left Fine –tuning (Mode 2)

8. Power ON/OFF

9. Left Fine –tuning (Mode 1) / Sideward Finetuning (Mode 2)
10. Left control lever
Installation methods of battery: Open back battery cover of remote control, and
put 4 No.5 alkaline batteries in the middle place correctly, according to battery
box's pole indication (battery should be available separately).
1. Install batteries with correct polarity.
2. Do not mix old and new batteries.
3. Do not mix different types of batteries.
3. Remote control keypad and LCD manual
01. Sideward Fine-tuning: Power-on start in the centering. (Be turn Left/Right
Fine -tuning in Mode2)
02. Forward/Backward fine-tuning: Power-on start in the middle.
03. Turn Left/Right fine-tuning:Power-on start in centering. (Be Sideward Fly
Fine -tuning in Mode2)
04. Forward shows: Power-on start in the lowest level. (At the center square)
05. Backward shows: Power-on start in the lowest level. (At the center square)
06. Right sideward fly shows: Power-on start in the lowest level. (At the center
square)
07. Left sideward fly shows: Power-on start in the lowest level. (At the center
All manuals and user guides at all-guides.com
square)
08. Turn left: Pull left function lever to left, it will be higher, than quad copter
turn left faster.
09. Turn right: Pull left function lever to right, it will be higher, than quad copter
turn right faster.
10. High/Low speed: Press button "A" for seconds to switch between high
speed mode or low speed mode. "H" means high speed and "L" means low
speed.
11. Power shows: According to the battery's energy for the controller.
12. Default mode when power-on. When change to MODE 2, please keep
pressing button "B" to right than return on the power of transmitter, the MODE
on LCD displayer will be changed. Same steps to change
to MODE 1 again.
13. Signal shows: Normally to full frame.
4. Install landing skids & blade protecting frame
1. Insert foot stands into interface of lower main body as shown in Figure (1).
2. Install the blade protecting frame to every corner than lock screws (Figure
2-3).
5. Component installation of WI-FI real-time aerial photo
Installation of phone attaching clamp
1. Insert phone attaching clamp by aiming at antenna on remote control.
2. Press spring of attaching clamp forcibly to resize.
3. Hold phone attaching clamp and pull out forcibly to disassemble phone
attaching clamp.
6. WI-FI software download and installation
Install software
1. For Android phone, please download from www.symatoys.com or scan
two-dimension code to install SYMA FPV software.
For iphone IOS, please download from App Store to install SYMA FPV
software or scan two-dimension code to install SYMA FPV software.
Warm remind: two-dimension code is provided in color box packaging and back
cover of specification to scan. (
2. Connection description
When connecting with model power, indicator light of FPV is green light. Red
light flashes slowly after 20 seconds for waiting to connect with the phone.
Click "setting" of the phone, open WIFI, find out "FPV WIFI****" in WIFI
searching list, click connection until it appears "connected", indicating
successful connection, and now exit setting option. Open SYMA FPV software,
click "START" button and enter into control interface. Image is showing on
phone screen. WIFI signal is full, showing the strongest signal right now.
1. Open the software SYMA FPV.
2. Click the "START" button.
3. Image is showing on the screen.
3. Icon description of real-time interface
1. Return
2. WIFI signal
3. Phone and video check
4. Video
5. Photograph
6. Time display
4. Real-time aerial photo
Photo & video: when WIFI camera stays in normal state, click photo or video
icon on the real-time interface to take pictures or video (files of photo or video
can be checked in the folder of "photo and video check").
7. Controller modes & instructions
The transmitter built-in two modes, Mode 1 & Mode 2, in line with different
customer's usage pattern. Keep pushing button B to right, then turn on the
transmitter power to change Mode 1 or Mode 2.
8. MODE 1
Operating direction
Hover up and down: Push the throttle up or down, the quadcopter flies upward
or downward.
Forward and backward: Push the direction lever up or down, the quadcopter
flies forward or backward.
Turn left and right: Pull the throttle left or left, the quadcopter turns to left or
right.
Sideward fly: Pull the direction lever right or right, the quadcopter flies to left
side or right side.
Fine-tuning operation
Forward/Backward fine-tuning
When the quadcopter keeps flying forward / backward, you can correct it by
pressing fine-tuning button down / up.
Sideward fly fine-tuning
When the quadcopter keeps flying to left / right side, you can correct it by
pressing the Fine-tuning button right / left.
Turn left/right fine-tuning
When the quadcopter keeps rotating to left / right, you can correct it by
pressing the finetuning button right / left.
8
*
)