Publicidad
4
BB 560M
コントロールとコネクタ
すばやく押すと音
(1) VOLUME + / NEXT SONG -
量が上がり、 長押しすると次の曲にスキ
ップします。
ペアリング、 再生、 一
(2) PLAY/PAUSE - Bluetooth
時停止、 電話を切る、 通話を拒否、 リダイ
ヤルなど、 いく つかの機能に使用されま
す。 このボタンを
秒間押し続けると、
1
ヘッドホンがオンになります。
すばやく押すと
(3) VOLUME - / PREVIOUS SONG -
音量が下がり、 長押しすると前の曲にな
ります。
有線オーディオ用に
(4) 3.5 mm INPUT -
3.5 mm
ステレオケーブルを接続します。
赤と青のステータスインジケータラ
(5) LED -
イト。
(6) MICROPHONE
赤と青のステータスインジケー
(7) USB PORT -
タライト。
控件和连接器
(1) VOLUME + / NEXT SONG -
快速按下以增大音
量， 按住不放可跳至下一首歌曲。
(2) PLAY/PAUSE -
用于多种功能， 包括蓝牙配
对， 播放， 暂停， 挂断， 拒绝呼叫和重拨。
1
按住此按钮
秒钟以打开耳机。
(3) VOLUME - / PREVIOUS SONG -
快速按下以降低
音量， 并按住以播放上一首歌曲。
(4) 3.5 mm INPUT -
3.5
连接
毫米立体声电缆以
用于有线音频。
(5) LED -
红色和蓝色状态指示灯。
(6) MICROPHONE
(7) USB PORT -
Micro USB
用于充电的
端口。
Charging
After unpacking the headphones, the USB charging cable should
be plugged in and allowed to charge for at least 4 hours. Once
the battery has been fully charged the first time, subsequent
charges should only take 2-3 hours. While charging, the LED
will light red. After the battery has reached full capacity, the LED
will turn off.
The headset will beep twice to indicate that the battery power
is low, and the LED will flash red. When the voltage drops
below 3 V, the headset will automatically power off and must
be recharged.
Pairing of headset and
Bluetooth device
1. Turn on the headphones by holding the Play/Pause button
for 1 second. The LED will alternate flashing red and blue
and a sound will beep twice to indicate that the device is
ready for pairing.
2. Open the Bluetooth menu on your Bluetooth device
and search for available connections. Note that if the
headset does not successfully pair with a device, it will
automatically power down after 3 minutes.
3. Select "BB 560M" from the list. When pairing is successful,
the headset will beep once and the LED will light blue.
If a password is required, use "0000".
Once the headset has been successfully pair with another
device, it will automatically try to connect to this same device
when the headset is powered off and powered on again.
Quick Start Guide
Bluetooth wireless call
When the Bluetooth headset is paired and connected with
your mobile phone, you can use the headset to accept phone
calls in addition to listening to music.
Outgoing calls
1. To make a new call while using the headset, dial a number
as usual. A ringing tone will be heard in the headset and
the voice audio and microphone will automatically be
switched to the headset. (note that some phones require
the switch to be confirmed manually on the screen)
2. To redial the last number, double click the Play/Pause
button to dial out the last dialing phone number. (Some
mobile phones may only require a single press of the button.)
Answering and hanging up calls
1. When the phone rings, press the Play/Pause
button
once or press the phone answer key to answer the phone.
2. To reject the call, press and hold the Play/Pause
button
for 1 second.
3. To end a call, press the Play/Pause button
or press the
hang up button on the phone screen. After the call ends,
any music that was playing prior to the call will resume.
IMPORTANT SAFETY INFORMATION
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not throw this product in the fire, to avoid explosion.
8. Do not expose this product to bright sunshine for a long time.
9. Do not disassemble or modify this product.
10. Please store this product in a clean and dry environment.
5
Publicidad
