Normal Sounds - Hisense AP0819CR1W Instrucciones De Uso E Instalación

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

DIMMER
Press the DIMMER button to turn off the control panel display.
NOTE:
When in DIMMER mode, new control inputs will return display
to normal.
Sleep mode
SLEEP mode can only be set in Cooling, Heating or Drying
modes. When in sleep mode the unit will utilize lower, quieter
fanspeeds and automatic temperature adjustments offering 8
hours of optimal sleeping conditions before shutting off.
NOTE:
The appliance will stop operation automatically after operating
for 8 hours.
Fan speed is automatically set at low speed.
In the Cooling mode, if the current room temperature is
below 79°F(26°C), the temperature will automatically
increase 1°F(1°C) during the first hour after Sleep control
is activated, and continue running at that temperature.
If the room temperature is 79°F(26°C) or above, set
temperature will not change.
In Heating mode, the set temperature will decrease by 6°F(3°C)
at most, during 3 hours, and continues running at that
temperature until auto shut off.
1. Press MODE to select COOL, Heating or DRY.
NOTE: Sleep control cannot be selected in Fan mode.
2. Press the UP or DOWN button to set the temperature.
Press and hold the DIMMER button on the remote for 5
3.
seconds to switch the DIMMER mode to the Sleep mode.
4. After 5 seconds, the lights on the control panel display will dim.
NOTE: The temperature and airflow direction may be
adjusted during Sleep control. The fan speed is automatically
set to Low speed. After 5 seconds, the lights on the control
panel display will dim again.
5. To turn off Sleep control, press MODE, FAN, Sleep or wait
8 hours for Sleep control to turn off automatically.
NOTE: The air conditioner will return to previous settings
after Sleep mode is turned off.
TIMER
Use the TIMER function to turn the air conditioner ON/OFF
automatically.
Setting the Air Conditioner to Turn On:
1.Plug in the air conditioner and use the remote to power it
ON.
2.Use the remote to set the desired mode, temperature, fan
speed, etc.
3.Use the remote to power OFF the air conditioner.
4.Press TIMER on the remote and use the UP, DOWN
buttons to set the desired delay time until the air conditioner
turns ON. The delay time can be set from 0 to 24 hours in
one-hour increments.
5.Press TIMER again to confirm the delay time. The TIMER
light on the unit will be on.
Setting the Air Conditioner to Turn OFF:
1.Plug in the air conditioner and use the remote to power it
ON.
2.Use the remote to set the desired mode, temperature, fan
speed, etc.
3.Press TIMER on the remote and use the UP, DOWN
buttons to set the desired delay time until the air conditioner
turns OFF. The delay time can be set from 0 to 24 hours in
one-hour increments.
4.Press TIMER again to confirm the delay time. The TIMER
light on the unit will be on.
To cancel TIMER :
Press the TIMER button again. Once a "beep" is heard and
the indicator disappears, the TIMER mode has been
canceled.
NOTE:
The TIMER function can only be set by the remote control.
SWING
Press SWING once to change the vertical airflow direction.
Press again to hold the louver in a desired position.
NOTE:
Swing function is not available on this models.
When your air conditioner is operating normally, you may hear
sounds such as:
Air movement from the fan.
Clicks from the thermostat cycling.
Vibration or noise due to poor wall or window construction.
A high-pitched hum or pulsating noise caused by the
high-efficiency compressor cycling on and off.
1 4

Normal Sounds

Publicidad

Capítulos

Tabla de contenido

Solución de problemas

loading

Tabla de contenido